2022–present · pickup

Toyota Tundra 3rd gen (XK70) wheel fitment

The third-generation Tundra changed to six-stud wheels, so previous-generation factory wheels do not transfer across. Aftermarket builds commonly use 18-inch wheels for taller tyre sidewalls, with positive offsets to limit the amount of trimming.

6x139.7 bolt pattern · 95.1 mm centre bore · Stock wheels: 18 × 7.5, 20 × 8, 20 × 8.5, 22 × 8 inch · Stock tyres: 265/70 R18, 265/60 R20, 265/50 R22

Updated 2026-10-04 · Medium source confidence. Check your exact trim and market. How we check specs

Quick specs

Toyota Tundra 3rd gen (XK70) hub and fastener specifications
Specification	Value
Bolt pattern	6x139.7
Stock tyre sizes	265/70 R18 265/60 R20 265/50 R22
Centre bore	95.1 mm
Fastener and thread	Wheel nut, M14x1.5
Tightening torque	131 Nm (confirm in your handbook)

Stock wheels and tyres

Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.

Factory wheels and tyres by trim and axle
Trim	Axle	Wheel	Tyre
SR5, standard alloy / 18-inch TRD Off-Road	Front and rear	18 × 7.5 inch, ET60	265/70 R18
Limited / Platinum / 1794, standard 20-inch package	Front and rear	20 × 8 inch, ET60	265/60 R20
TRD Off-Road optional 20-inch package, PT946-34221-F2	Front and rear	20 × 8.5 inch, ET55	265/60 R20
Capstone	Front and rear	22 × 8 inch, ET60	265/50 R22

Explained in our guides

Read these before choosing wheels for the Tundra: they explain the offset, fitment and hub numbers in this guide.

Popular community setups

Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.

Stock-height all-terrain setup

Front and rear: 18 × 9 inch, ET18 · 33x12.50 R18

An owner documents KMC wheels and Toyo Open Country AT3 tyres at standard height without rubbing. Check full travel and tyre-specific dimensions.

Lifted 35-inch setup

Front and rear: 18 × 9 inch, ET18 · 35x12.50 R18

TORQ recommends this with its 3-inch front and 1.5-inch rear lift. Minor trimming may still be needed.

20-inch lifted daily

Front and rear: 20 × 9 inch, ET18 · 295/60 R20

Listed by TORQ for its lift packages. Allow for liner clearance work and check the spare tyre arrangement.

Width and offset guidance

Offset range

Check the exact setup

There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.

Common width limit

Measure before ordering

A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.

These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.

Clearance notes

Toyota specifies 131 Nm for factory aluminium wheels and 209 Nm for steel wheels. The single torque field records the aluminium-wheel value.
Wheel suppliers variously label the hub 95, 95.1 or 95.2 mm. The nominal 95.1 mm listing here must be checked against the wheel manufacturer's XK70 application.
The older five-stud Tundra uses 5x150 and a larger hub; its wheels do not bolt onto the XK70.
The SR steel and TRD Pro factory rows are omitted because published wheel widths conflict. Toyota confirms 245/75 R18 on SR and 285/65 R18 on the TRD Pro, but that does not establish a complete wheel specification.
Negative offsets increase tyre sweep into the bumper and liners. Do not infer full compression clearance from a parked truck.
The 20-inch TRD Off-Road wheel listed here is 8.5 inches wide at ET55; it is not the same wheel as the standard 8-inch ET60 package. Some replacement-wheel catalogue rows contain an incorrect five-lug label; Toyota specifies six studs for XK70.
Check full steering lock and suspension travel with the car loaded. Match wheel load rating, tyre load and speed ratings, fastener seats and brake clearance.

See it on your car.

Upload a photo and start with a look that suits the Tundra. Try the wheels, colour and stance before you spend on parts.

See it on your car

An AI preview shows the look. It cannot verify physical fitment.

Run the numbers

These tools start with the SR5, standard alloy / 18-inch TRD Off-Road front size. Choose your own trim or axle in the calculator if it differs.

Compare tyre sizes Compare wheel offsets Check tyre and rim width Find the same bolt pattern Convert offset to backspacing

Questions

What is the bolt pattern of the 2022-on Tundra?

It is 6x139.7 with M14x1.5 wheel nuts. The previous Tundra used 5x150.

Do all Tundra wheels use the same tightening torque?

No. Toyota specifies 131 Nm for aluminium wheels and 209 Nm for steel wheels on this generation.

Can I fit 35-inch tyres without trimming?

Not as a universal fit. A documented 18x9 ET18 setup uses a suspension lift and may still need minor trimming.

What tyres come on the Capstone?

The documented 2022 Capstone package uses 265/50 R22 tyres on 22x8 ET60 wheels.

What wheel size does the Toyota Tundra 3rd gen (XK70) use?

Factory wheels are 18 × 7.5 inch, 20 × 8 inch, 20 × 8.5 inch and 22 × 8 inch, depending on trim. The stock table lists the offset for each.

What is the Toyota Tundra 3rd gen (XK70) centre bore?

95.1 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.

Specs checked against

This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.

Related cars

More guides from Toyota or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.