2024–present · pickup

Toyota Tacoma 4th gen (N400) wheel fitment

The fourth-generation Tacoma keeps the six-stud pattern but changes the hub and wheel hardware. Owners commonly use positive-offset 17-inch aftermarket wheels with larger all-terrain tyres, or retain the factory 18-inch packages.

6x139.7 bolt pattern · 95.1 mm centre bore · Stock wheels: 17 × 7.5, 18 × 7.5, 18 × 8.5 inch · Stock tyres: 245/70 R17, 265/70 R17, 265/65 R18, 265/70 R18

Updated 2026-10-04 · Medium source confidence. Check your exact trim and market. How we check specs

Quick specs

Toyota Tacoma 4th gen (N400) hub and fastener specifications
Specification	Value
Bolt pattern	6x139.7
Stock tyre sizes	245/70 R17 265/70 R17 265/65 R18 265/70 R18
Centre bore	95.1 mm
Fastener and thread	Wheel nut, M14x1.5
Tightening torque	131 Nm (confirm in your handbook)

Stock wheels and tyres

Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.

Factory wheels and tyres by trim and axle
Trim	Axle	Wheel	Tyre
SR5, 17-inch alloy option	Front and rear	17 × 7.5 inch, ET55	245/70 R17
TRD Off-Road / TRD PreRunner	Front and rear	17 × 7.5 inch, ET55	265/70 R17
TRD Sport / Limited	Front and rear	18 × 7.5 inch, ET55	265/65 R18
Trailhunter	Front and rear	18 × 8.5 inch, ET20	265/70 R18

Explained in our guides

Read these before choosing wheels for the Tacoma: they explain the offset, fitment and hub numbers in this guide.

Popular community setups

Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.

33-inch daily and trail

Front and rear: 17 × 8.5 inch, ET25 · 285/70 R17

Owners report this on standard TRD Off-Road suspension. Larger Canadian mudflaps have needed trimming; check clearance under compression.

Taller tyres with a levelling kit

Front and rear: 17 × 8.5 inch, ET25 · 285/75 R17

Documented with Method MR305 wheels and a Westcott levelling kit. Check mudflaps, liners and full-lock clearance rather than assuming every tyre clears.

Width and offset guidance

Offset range

Check the exact setup

There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.

Common width limit

Measure before ordering

A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.

These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.

Clearance notes

The 131 Nm torque figure applies to factory aluminium wheels. Toyota specifies 209 Nm for the applicable steel wheels.
Retailers describe the nominal hub as 95.1 mm, while some catalogues round it to 95 or 95.2 mm. Order a wheel specifically approved for the fourth-generation Tacoma.
Third-generation Tacoma wheels are not a direct factory swap: the hub bore, stud diameter and lug seating arrangements differ.
Stock entries cover the listed alloy packages. Base steel wheels and the TRD Pro package are not assigned an offset here because the consulted catalogues conflict.
A 17-inch wheel still needs confirmed brake and spoke clearance; diameter alone is insufficient.
Check full steering lock and suspension travel with the car loaded. Match wheel load rating, tyre load and speed ratings, fastener seats and brake clearance.

See it on your car.

Upload a photo and start with a look that suits the Tacoma. Try the wheels, colour and stance before you spend on parts.

See it on your car

An AI preview shows the look. It cannot verify physical fitment.

Run the numbers

These tools start with the SR5, 17-inch alloy option front size. Choose your own trim or axle in the calculator if it differs.

Compare tyre sizes Compare wheel offsets Check tyre and rim width Find the same bolt pattern Convert offset to backspacing

Questions

Did the Tacoma bolt pattern change in 2024?

The pattern remains 6x139.7, but the hub became smaller and the studs changed to M14x1.5.

Will 285/70 R17 tyres fit without a lift?

Owners have run them on 17x8.5 ET25 wheels with standard TRD Off-Road suspension. Mudflap shape and tyre construction can still cause rubbing.

What torque should I use on fourth-generation Tacoma wheels?

Toyota specifies 131 Nm for aluminium wheels and 209 Nm for the applicable steel wheels.

What offset are the factory TRD Sport wheels?

The documented 2024 TRD Sport wheels are 18x7.5 ET55 with 265/65 R18 tyres.

What size tyres does the Toyota Tacoma 4th gen (N400) have?

Factory tyre (tire) sizes for the 2024–present Toyota Tacoma 4th gen (N400) are 245/70 R17, 265/70 R17, 265/65 R18 and 265/70 R18, depending on trim. Your tyre placard shows the size for your car.

What wheel size does the Toyota Tacoma 4th gen (N400) use?

Factory wheels are 17 × 7.5 inch, 18 × 7.5 inch and 18 × 8.5 inch, depending on trim. The stock table lists the offset for each.

What is the Toyota Tacoma 4th gen (N400) centre bore?

95.1 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.

Specs checked against

This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.

Related cars

More guides from Toyota or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.