2016–2023 · pickup

Toyota Tacoma 3rd gen (N300) wheel fitment

The third-generation Tacoma is commonly fitted with 16- or 17-inch wheels and all-terrain tyres. Mild builds retain near-standard tyre diameters, while 33-inch setups need closer attention to the front body mounts and wheelarch liners.

6x139.7 bolt pattern · 106.1 mm centre bore · Stock wheels: 16 × 7, 17 × 7.5, 18 × 7.5 inch · Stock tyres: 245/75 R16, 265/70 R16, 265/65 R17, 265/60 R18

Updated 2026-10-04 · High source confidence. Check your exact trim and market. How we check specs

Quick specs

Toyota Tacoma 3rd gen (N300) hub and fastener specifications
Specification	Value
Bolt pattern	6x139.7
Stock tyre sizes	245/75 R16 265/70 R16 265/65 R17 265/60 R18
Centre bore	106.1 mm
Fastener and thread	Wheel nut, M12x1.5
Tightening torque	113 Nm (confirm in your handbook)

Stock wheels and tyres

Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.

Factory wheels and tyres by trim and axle
Trim	Axle	Wheel	Tyre
SR / SR5, standard 16-inch wheels	Front and rear	16 × 7 inch, ET25	245/75 R16
TRD Off-Road	Front and rear	16 × 7 inch, ET25	265/70 R16
TRD Sport	Front and rear	17 × 7.5 inch, ET30	265/65 R17
Limited	Front and rear	18 × 7.5 inch, ET30	265/60 R18

Explained in our guides

Read these before choosing wheels for the Tacoma: they explain the offset, fitment and hub numbers in this guide.

Popular community setups

Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.

Factory wheels with taller all-terrains

Front and rear: 16 × 7 inch, ET25 · 265/75 R16

Documented on standard TRD Off-Road alloys without rubbing. Check mudflap clearance with the chosen tyre.

TRD wheel swap and mild lift

Front and rear: 17 × 7 inch, ET4 · 275/70 R17

Documented with 4Runner TRD wheels and a Toyota lift of roughly 2 inches front and 1 inch rear. Front mudflaps and liners need checking.

Lifted 33-inch trail setup

Front and rear: 17 × 8.5 inch, ET0 · 285/70 R17

A common aftermarket combination with a levelling or suspension lift. Tyre shape and alignment determine whether liner trimming or body-mount clearance work is needed.

Width and offset guidance

Offset range

Check the exact setup

There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.

Common width limit

Measure before ordering

A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.

These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.

Clearance notes

This guide covers six-stud 2016–2023 trucks, including two-wheel-drive versions. Earlier five-stud Tacoma specifications do not apply.
The ThreePiece guide incorrectly lists M14 hardware in its overview; this generation uses M12x1.5 nuts, confirmed by the wheel retailer and fitment database. Toyota specifies 113 Nm.
Choose nuts with the seat required by the wheel. Factory Toyota alloy shank nuts are not automatically suitable for aftermarket conical seats.
TRD Pro wheel designs changed during this generation; those stock rows are omitted rather than treating every Pro wheel as the same offset.
A lift alone does not guarantee clearance at full steering lock and suspension compression.
Check full steering lock and suspension travel with the car loaded. Match wheel load rating, tyre load and speed ratings, fastener seats and brake clearance.

See it on your car.

Upload a photo and start with a look that suits the Tacoma. Try the wheels, colour and stance before you spend on parts.

See it on your car

An AI preview shows the look. It cannot verify physical fitment.

Run the numbers

These tools start with the SR / SR5, standard 16-inch wheels front size. Choose your own trim or axle in the calculator if it differs.

Compare tyre sizes Compare wheel offsets Check tyre and rim width Find the same bolt pattern Convert offset to backspacing

Questions

What is the bolt pattern of a third-generation Tacoma?

All 2016–2023 Tacomas use 6x139.7 with a 106.1 mm centre bore and M12x1.5 wheel nuts.

Will 33-inch tyres fit a stock Tacoma?

Some combinations can be made to fit, but 285/70 R17 is not a guaranteed fit without rubbing. Wheel offset, alignment, liners and body mounts all matter.

Do fourth-generation Tacoma wheels fit a third-generation truck?

They are not a direct replacement. The newer wheels have a smaller centre bore and use different stud hardware.

What torque do Tacoma wheel nuts need?

Toyota specifies 113 Nm for the factory wheel installation on this generation.

What size tyres does the Toyota Tacoma 3rd gen (N300) have?

Factory tyre (tire) sizes for the 2016–2023 Toyota Tacoma 3rd gen (N300) are 245/75 R16, 265/70 R16, 265/65 R17 and 265/60 R18, depending on trim. Your tyre placard shows the size for your car.

What wheel size does the Toyota Tacoma 3rd gen (N300) use?

Factory wheels are 16 × 7 inch, 17 × 7.5 inch and 18 × 7.5 inch, depending on trim. The stock table lists the offset for each.

What is the Toyota Tacoma 3rd gen (N300) centre bore?

106.1 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.

Specs checked against

This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.

Related cars

More guides from Toyota or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.