18-inch touring
- Front and rear
- 18 × 9 inch, ET35 · 285/65 R18
The Wheel Deal documents this combination with ROH Onyx wheels. Verify liner clearance at full travel and the load rating for any GVM upgrade.
2021–present · SUV
Toyota Land Cruiser 300 Series wheel fitment
The 300 Series uses six-stud wheels with a smaller hub bore than many older six-stud Toyotas. Touring builds commonly retain 18-inch wheels while increasing tyre size and reducing the factory positive offset.
6x139.7 bolt pattern · 95.1 mm centre bore · Stock wheels: 18 × 7.5, 20 × 8 inch · Stock tyres: 265/65 R18, 265/55 R20
Updated 2026-10-04 · High source confidence. Check your exact trim and market. How we check specs
Quick specs
| Specification | Value |
|---|---|
| Bolt pattern | |
| Stock tyre sizes | |
| Centre bore | 95.1 mm |
| Fastener and thread | Wheel nut, M14x1.5 |
| Tightening torque | 131 Nm (confirm in your handbook) |
Stock wheels and tyres
Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.
| Trim | Axle | Wheel | Tyre |
|---|---|---|---|
| Japanese GX / AX / VX / GR Sport, 18-inch alloy | Front and rear | 18 × 7.5 inch, ET60 | 265/65 R18 |
| Japanese ZX, 20-inch alloy | Front and rear | 20 × 8 inch, ET60 | 265/55 R20 |
Explained in our guides
Read these before choosing wheels for the Land Cruiser: they explain the offset, fitment and hub numbers in this guide.
- Wheel offset explained: choosing ET without guessingUnderstand positive and negative wheel offset, calculate inner clearance and outer position, and choose an ET using measurements from your own car.
- Lifted truck wheel fitment: backspacing, 33s, 35s and trimmingPlan larger truck tyres around lift-kit requirements, backspacing, steering and articulation. Compare 33 and 35 inch tyres without assuming a lift guarantees clearance.
- Hub-centric vs lug-centric wheels: choosing hub ringsLearn what hub rings do, how to specify their inner and outer diameters, and why centring, wheel seats and vibration need separate checks.
Popular community setups
Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.
Wider off-road stance
- Front and rear
- 18 × 9 inch, ET18 · 285/65 R18
Prestige Tyre and Auto documents Method 314 wheels with Yokohama G016 tyres. This lower offset pushes the tyre further out; check guard coverage and steering clearance.
Width and offset guidance
Offset range
Check the exact setup
There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.
Common width limit
Measure before ordering
A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.
These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.
Clearance notes
- The 131 Nm field is for aluminium wheels. Toyota service information reproduced by JMACX specifies 209 Nm for steel wheels.
- Some Japanese references round the hub to 95 mm; application listings use nominal 95.1 mm. Order against the LC300 application.
- Factory packages here are Japanese-market examples. Australian and other market trim names and tyres can differ.
- Do not transfer LC200 wheel specifications to the LC300. Confirm the six-stud mounting, nut seat and brake clearance.
- A wheel approved for the standard vehicle may not meet the requirements of a GVM conversion.
- Check full steering lock and suspension travel with the car loaded. Match wheel load rating, tyre load and speed ratings, fastener seats and brake clearance.
See it on your car.
Upload a photo and start with a look that suits the Land Cruiser. Try the wheels, colour and stance before you spend on parts.
An AI preview shows the look. It cannot verify physical fitment.
Run the numbers
These tools start with the Japanese GX / AX / VX / GR Sport, 18-inch alloy front size. Choose your own trim or axle in the calculator if it differs.
Questions
What is the LC300 bolt pattern?
It is 6x139.7, with M14x1.5 nuts and a nominal 95.1 mm centre bore.
What is the LC300 wheel nut torque?
Toyota specifies 131 Nm for aluminium wheels and 209 Nm for steel wheels.
What tyres do modified LC300s commonly run on 18-inch wheels?
Documented retailer builds use 285/65 R18 on 18x9 wheels at ET35 or ET18. The lower offset needs more attention to guard coverage and rubbing.
What wheel size does the Toyota Land Cruiser 300 Series use?
Factory wheels are 18 × 7.5 inch and 20 × 8 inch, depending on trim. The stock table lists the offset for each.
What is the Toyota Land Cruiser 300 Series centre bore?
95.1 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.
Specs checked against
- Toyota: LC300 tyres, wheels and torque
- MYG Lab: LC300 factory offsets and hardware
- Koleso: LC300 mounting data
- JMACX: Toyota steel and aluminium wheel torque
- The Wheel Deal: LC300 ROH Onyx build
- Prestige Tyre and Auto: LC300 Method build
This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.
Related cars
More guides from Toyota or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.
Toyota 4Runner 4th gen / N210
2003–2009 · 6x139.7
Toyota 4Runner 5th gen (N280)
2010–2024 · 6x139.7
Toyota Auris E180, 2nd gen
2012–2018 · 5x114.3
Toyota Chaser JZX100
1996–2001 · 5x114.3
Toyota Corolla E210, North American non-GR
2018–present · 5x100
Toyota Corolla Levin / Sprinter Trueno AE86
1983–1987 · 4x114.3