2007–2021 · SUV

Toyota Land Cruiser 200 Series (J200) wheel fitment

The 200 Series is commonly modified for touring with taller all-terrain tyres and smaller-diameter wheels. Its five-stud hubs differ from the six-stud Prado and newer Land Cruisers, so wheel searches need to specify the 200 Series.

5x150 bolt pattern · 110.1 mm centre bore · Stock wheels: 17 × 8, 18 × 8, 20 × 8.5 inch · Stock tyres: 285/65 R17, 285/60 R18, 285/50 R20

Updated 2026-10-04 · Medium source confidence. Check your exact trim and market. How we check specs

Quick specs

Toyota Land Cruiser 200 Series (J200) hub and fastener specifications
Specification	Value
Bolt pattern	5x150
Stock tyre sizes	285/65 R17 285/60 R18 285/50 R20
Centre bore	110.1 mm
Fastener and thread	Wheel nut, M14x1.5
Tightening torque	131 Nm (confirm in your handbook)

Stock wheels and tyres

Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.

Factory wheels and tyres by trim and axle
Trim	Axle	Wheel	Tyre
Selected global-market 17-inch alloy package	Front and rear	17 × 8 inch, ET60	285/65 R17
US standard / global 18-inch alloy package	Front and rear	18 × 8 inch, ET60	285/60 R18
Selected global-market upper grades, 20-inch package	Front and rear	20 × 8.5 inch, ET60	285/50 R20

Explained in our guides

Read these before choosing wheels for the Land Cruiser: they explain the offset, fitment and hub numbers in this guide.

Popular community setups

Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.

Rock Warrior wheel swap

Front and rear: 17 × 8 inch, ET50 · 285/70 R17

Documented on a 2013 Land Cruiser using Toyota TRD Rock Warrior wheels. Confirm wheel barrel clearance for the exact brake package.

Wider 33-inch touring setup

Front and rear: 17 × 8.5 inch, ET25 · 285/70 R17

Owners report this combination with Icon wheels. Liner relocation and front mudflap trimming may be required, even without a large suspension lift.

Width and offset guidance

Offset range

Check the exact setup

There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.

Common width limit

Measure before ordering

A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.

These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.

Clearance notes

This covers J200 only. Prado, 70 Series, 250 Series and 300 Series wheel data must not be substituted.
The nominal centre bore is commonly listed as 110.1 mm and rounded to 110 mm in other catalogues. Use a wheel approved for J200 hubs.
The 131 Nm figure is Toyota's factory alloy-wheel value. Confirm the applicable manual for steel-wheel variants.
Seventeen-inch fitment depends on wheel barrel and spoke shape, especially with changed brakes. A matching bolt pattern is insufficient.
The standard entries are market-specific wheel packages. Check the tyre placard rather than assuming every GX, GXL, VX or Sahara used the same size throughout production.
Check full steering lock and suspension travel with the car loaded. Match wheel load rating, tyre load and speed ratings, fastener seats and brake clearance.

See it on your car.

Upload a photo and start with a look that suits the Land Cruiser. Try the wheels, colour and stance before you spend on parts.

See it on your car

An AI preview shows the look. It cannot verify physical fitment.

Run the numbers

These tools start with the Selected global-market 17-inch alloy package front size. Choose your own trim or axle in the calculator if it differs.

Compare tyre sizes Compare wheel offsets Check tyre and rim width Find the same bolt pattern Convert offset to backspacing

Questions

What is the bolt pattern of the Land Cruiser 200?

The J200 uses 5x150, M14x1.5 wheel nuts and a nominal 110.1 mm centre bore.

Will six-stud Land Cruiser wheels fit a 200 Series?

No. The bolt pattern is different, including on newer 250 and 300 Series wheels.

Can I use 17-inch wheels on a 200 Series?

Yes, suitable 17-inch wheels are documented, including Toyota Rock Warriors. Confirm clearance for the exact wheel and brake package.

Do 285/70 R17 tyres need trimming?

They can. With wider ET25 wheels, owners report relocating liners and trimming front mudflaps to gain steering clearance.

What size tyres does the Toyota Land Cruiser 200 Series (J200) have?

Factory tyre (tire) sizes for the 2007–2021 Toyota Land Cruiser 200 Series (J200) are 285/65 R17, 285/60 R18 and 285/50 R20, depending on trim. Your tyre placard shows the size for your car.

What wheel size does the Toyota Land Cruiser 200 Series (J200) use?

Factory wheels are 17 × 8 inch, 18 × 8 inch and 20 × 8.5 inch, depending on trim. The stock table lists the offset for each.

What is the Toyota Land Cruiser 200 Series (J200) centre bore?

110.1 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.

What is the Toyota Land Cruiser 200 Series (J200) wheel nut torque?

131 Nm (about 97 lb-ft) for the original nuts. Confirm in your handbook, especially with aftermarket wheels or nuts.

Specs checked against

This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.

Related cars

More guides from Toyota or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.