1998–2007 · SUV

Toyota Land Cruiser 100 Series wheel fitment

The 100 Series commonly keeps a tall tyre sidewall for touring and off-road use. Owners often retain the factory wheels with larger all-terrain tyres, while wider aftermarket wheels need particular care over offset.

5x150 bolt pattern · 110.1 mm centre bore · Stock wheels: 16 × 8, 17 × 8, 18 × 8 inch · Stock tyres: 275/70 R16, 275/65 R17, 275/60 R18

Updated 2026-10-04 · High source confidence. Check your exact trim and market. How we check specs

Quick specs

Toyota Land Cruiser 100 Series hub and fastener specifications
Specification	Value
Bolt pattern	5x150
Stock tyre sizes	275/70 R16 275/65 R17 275/60 R18
Centre bore	110.1 mm
Fastener and thread	Wheel nut, M14x1.5
Tightening torque	131 Nm (confirm in your handbook)

Stock wheels and tyres

Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.

Factory wheels and tyres by trim and axle
Trim	Axle	Wheel	Tyre
Early wide-body alloy package	Front and rear	16 × 8 inch, ET60	275/70 R16
Later 17-inch alloy package	Front and rear	17 × 8 inch, ET60	275/65 R17
Late 18-inch alloy package, market dependent	Front and rear	18 × 8 inch, ET60	275/60 R18

Explained in our guides

Read these before choosing wheels for the Land Cruiser: they explain the offset, fitment and hub numbers in this guide.

Popular community setups

Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.

Original wheels with taller all-terrains

Front and rear: 16 × 8 inch, ET60 · 285/75 R16

Widely reported on standard-height 100 Series cars. Check individual tyre shoulders at steering lock and full compression.

17-inch touring on original wheels

Front and rear: 17 × 8 inch, ET60 · 285/70 R17

Owner-reported alternative retaining the factory offset. Check clearance throughout travel and whether the larger spare fits its carrier.

Width and offset guidance

Offset range

Check the exact setup

There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.

Common width limit

Measure before ordering

A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.

These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.

Clearance notes

These entries cover the independent-front-suspension 100, not the solid-front-axle 105, whose wheel offsets differ.
Weds lists a 110 mm vehicle hub; wheel catalogues commonly call the matching bore 110.1 mm.
Toyota specifies 131 Nm for the alloy-wheel packages covered here. Check the handbook for any different original steel-wheel package.
Factory alloy nuts and aftermarket tapered nuts are not interchangeable unless the wheel manufacturer explicitly specifies that seat.
Check full steering lock and suspension travel with the car loaded. Match wheel load rating, tyre load and speed ratings, fastener seats and brake clearance.

See it on your car.

Upload a photo and start with a look that suits the Land Cruiser. Try the wheels, colour and stance before you spend on parts.

See it on your car

An AI preview shows the look. It cannot verify physical fitment.

Run the numbers

These tools start with the Early wide-body alloy package front size. Choose your own trim or axle in the calculator if it differs.

Compare tyre sizes Compare wheel offsets Check tyre and rim width Find the same bolt pattern Convert offset to backspacing

Questions

What is the Land Cruiser 100 bolt pattern?

It is 5x150, with M14x1.5 wheel nuts and a nominal 110.1 mm wheel bore.

Will 285/75 R16 tyres fit a standard 100 Series?

Many owners report using them on the original 16x8 ET60 wheels without a lift. Confirm clearance on the actual tyre and vehicle.

Can I use 105 Series wheels on a 100?

Do not treat them as equivalent. The 100's factory alloy packages use ET60; the solid-axle 105 has different offset requirements.

What size tyres does the Toyota Land Cruiser 100 Series have?

Factory tyre (tire) sizes for the 1998–2007 Toyota Land Cruiser 100 Series are 275/70 R16, 275/65 R17 and 275/60 R18, depending on trim. Your tyre placard shows the size for your car.

What wheel size does the Toyota Land Cruiser 100 Series use?

Factory wheels are 16 × 8 inch, 17 × 8 inch and 18 × 8 inch, depending on trim. The stock table lists the offset for each.

What is the Toyota Land Cruiser 100 Series centre bore?

110.1 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.

What is the Toyota Land Cruiser 100 Series wheel nut torque?

131 Nm (about 97 lb-ft) for the original nuts. Confirm in your handbook, especially with aftermarket wheels or nuts.

Specs checked against

This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.

Related cars

More guides from Toyota or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.