2020–present · hatchback

Toyota GR Yaris GXPA16 wheel fitment

The GR Yaris normally uses 18-inch wheels with the same tyre size on both axles. Owners often choose 8.5J replacements for road or track tyres, while keeping enough spoke clearance for the front brakes.

5x114.3 bolt pattern · 60.1 mm centre bore · Stock wheels: 18 × 8, 17 × 7 inch · Stock tyres: 225/40 R18, 205/45 R17

Updated 2026-10-04 · High source confidence. Check your exact trim and market. How we check specs

Quick specs

Toyota GR Yaris GXPA16 hub and fastener specifications
Specification	Value
Bolt pattern	5x114.3
Stock tyre sizes	225/40 R18 205/45 R17
Centre bore	60.1 mm
Fastener and thread	Wheel nut, M12x1.5
Tightening torque	103 Nm (confirm in your handbook)

Stock wheels and tyres

Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.

Factory wheels and tyres by trim and axle
Trim	Axle	Wheel	Tyre
Standard / Convenience Pack / Japanese RZ	Front and rear	18 × 8 inch, ET45	225/40 R18
Circuit Pack / RZ High Performance, forged BBS	Front and rear	18 × 8 inch, ET45	225/40 R18
Japanese RC, standard small-brake 17-inch package	Front and rear	17 × 7 inch, ET40	205/45 R17

Explained in our guides

Read these before choosing wheels for the GR Yaris: they explain the offset, fitment and hub numbers in this guide.

Popular community setups

Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.

8.5J daily

Front and rear: 18 × 8.5 inch, ET45 · 235/40 R18

GR-Zoo owners document Autec Clubracing wheels in this size with Goodyear Eagle F1 SuperSport tyres. Check the exact wheel's brake clearance.

Lower-offset track set

Front and rear: 18 × 8.5 inch, ET35 · 235/40 R18

A GR-Zoo owner documents Motegi MR145 wheels with Nankang AR-1 tyres. The report uses 60-degree taper nuts and measures thread engagement; repeat that check rather than assuming the factory nuts fit.

Width and offset guidance

Offset range

Check the exact setup

There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.

Common width limit

Measure before ordering

A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.

These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.

Clearance notes

These specifications cover the GXPA16 four-wheel-drive GR Yaris, not the front-wheel-drive MXPA12 RS.
The Japanese RC's 17-inch wheel package is associated with its smaller brakes. It does not establish that arbitrary 17-inch wheels clear Circuit Pack brakes.
Toyota specifies 103 Nm for original wheels. Forum suggestions of 120 Nm for aftermarket wheels are not the factory specification.
Match the wheel nut seat and verify stud engagement on replacement wheels; the factory alloy hardware may be unsuitable.
Check full steering lock and suspension travel with the car loaded. Match wheel load rating, tyre load and speed ratings, fastener seats and brake clearance.

See it on your car.

Upload a photo and start with a look that suits the GR Yaris. Try the wheels, colour and stance before you spend on parts.

See it on your car

An AI preview shows the look. It cannot verify physical fitment.

Run the numbers

These tools start with the Standard / Convenience Pack / Japanese RZ front size. Choose your own trim or axle in the calculator if it differs.

Compare tyre sizes Compare wheel offsets Check tyre and rim width Find the same bolt pattern Convert offset to backspacing

Questions

What is the GR Yaris bolt pattern?

The GXPA16 uses 5x114.3, a 60.1 mm centre bore and M12x1.5 wheel nuts.

Are Circuit Pack wheels a different size?

The standard cast and Circuit Pack forged wheels are both 18x8 ET45 with 225/40 R18 tyres.

Can I use 235 tyres on a GR Yaris?

Yes. Owners document 235/40 R18 on 18x8.5 wheels at ET45 and ET35, with wheel-specific brake and hardware checks.

What is the GR Yaris wheel nut torque?

Toyota specifies 103 Nm for the original wheel and nut arrangement.

What size tyres does the Toyota GR Yaris GXPA16 have?

Factory tyre (tire) sizes for the 2020–present Toyota GR Yaris GXPA16 are 225/40 R18 and 205/45 R17, depending on trim. Your tyre placard shows the size for your car.

What wheel size does the Toyota GR Yaris GXPA16 use?

Factory wheels are 18 × 8 inch and 17 × 7 inch, depending on trim. The stock table lists the offset for each.

What is the Toyota GR Yaris GXPA16 centre bore?

60.1 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.

Specs checked against

This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.

Related cars

More guides from Toyota or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.