2023–present · hatchback

Toyota GR Corolla GZEA14 wheel fitment

The GR Corolla uses wide 18-inch wheels and factory rear spacers. Common replacements range from an original-width road set to 9.5J wheels for track tyres, but stud engagement needs particular attention.

5x114.3 bolt pattern · 60.1 mm centre bore · Stock wheels: 18 × 8.5 inch · Stock tyres: 235/40 R18, 245/40 R18

Updated 2026-10-04 · Medium source confidence. Check your exact trim and market. How we check specs

Quick specs

Toyota GR Corolla GZEA14 hub and fastener specifications
Specification	Value
Bolt pattern	5x114.3
Stock tyre sizes	235/40 R18 245/40 R18
Centre bore	60.1 mm
Fastener and thread	Wheel nut, M12x1.5
Tightening torque	103 Nm (confirm in your handbook)

Stock wheels and tyres

Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.

Factory wheels and tyres by trim and axle
Trim	Axle	Wheel	Tyre
Core / Premium / Circuit Edition	Front and rear	18 × 8.5 inch, ET30	235/40 R18
Morizo Edition	Front and rear	18 × 8.5 inch, ET30	245/40 R18

Explained in our guides

Read these before choosing wheels for the GR Corolla: they explain the offset, fitment and hub numbers in this guide.

Popular community setups

Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.

Original-width road set

Front and rear: 18 × 8.5 inch, ET23 · 235/40 R18

Apex lists this size with the original tyre width. Retain the factory rear spacer arrangement and follow its extended-stud and conical-nut requirements.

Wider road and track

Front and rear: 18 × 9.5 inch, ET35 · 255/35 R18

Apex lists this as typically a direct fit after the required hardware changes. Additional negative camber is encouraged for wider tyre compounds.

265-section track tyre

Front and rear: 18 × 9.5 inch, ET35 · 265/35 R18

Apex recommends a mild increase in negative camber with this wider tyre. Keep the factory rear spacers and verify sufficient stud engagement.

Width and offset guidance

Offset range

Check the exact setup

There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.

Common width limit

Measure before ordering

A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.

These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.

Clearance notes

The listed offsets are the wheel markings, not offsets after subtracting the original 10 mm rear spacers. Preserve the factory rear spacer configuration for the cited fitments.
Apex requires extended studs and 60-degree conical nuts with its GR Corolla wheels. The factory stud and shank-nut arrangement can leave inadequate engagement with aftermarket wheels.
Use 103 Nm for the original wheel hardware, as specified in Toyota's installation instructions; some retailer guides round this incorrectly to 80 lb ft.
Brake clearance is specific to the wheel design. The ordinary Corolla's wheel specifications do not establish GR Corolla compatibility.
Check full steering lock and suspension travel with the car loaded. Match wheel load rating, tyre load and speed ratings, fastener seats and brake clearance.

See it on your car.

Upload a photo and start with a look that suits the GR Corolla. Try the wheels, colour and stance before you spend on parts.

See it on your car

An AI preview shows the look. It cannot verify physical fitment.

Run the numbers

These tools start with the Core / Premium / Circuit Edition front size. Choose your own trim or axle in the calculator if it differs.

Compare tyre sizes Compare wheel offsets Check tyre and rim width Find the same bolt pattern Convert offset to backspacing

Questions

What is the GR Corolla bolt pattern?

5x114.3, with a 60.1 mm centre bore and M12x1.5 nuts.

What are the stock GR Corolla wheel sizes?

18x8.5 ET30. Most trims use 235/40 R18 tyres; the Morizo Edition uses 245/40 R18.

Does a GR Corolla need extended wheel studs?

Apex requires them for its wheels, along with 60-degree conical nuts. Check the replacement wheel maker's engagement requirements.

Should I remove the factory GR Corolla rear spacers?

The fitments listed here assume the original 10 mm rear spacers remain fitted. Removing them changes the rear wheel position.

What size tyres does the Toyota GR Corolla GZEA14 have?

Factory tyre (tire) sizes for the 2023–present Toyota GR Corolla GZEA14 are 235/40 R18 and 245/40 R18, depending on trim. Your tyre placard shows the size for your car.

What is the Toyota GR Corolla GZEA14 centre bore?

60.1 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.

What is the Toyota GR Corolla GZEA14 wheel nut torque?

103 Nm (about 76 lb-ft) for the original nuts. Confirm in your handbook, especially with aftermarket wheels or nuts.

Specs checked against

This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.

Related cars

More guides from Toyota or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.