17x8 ET35
- Front and rear
- 17 × 8 inch, ET35 · 225/45 R17
In ToyotaNation's 10th-gen Corolla forum, an owner of a 2009 Corolla S says they run 17x8 ET35 wheels with 225/45 R17 tyres and that they fit well.
2009–2013 · saloon
Toyota Corolla E140 (North America) wheel fitment
The North American E140 Corolla is a high-volume saloon, and most wheel changes are a step up from the 15 or 16-inch factory wheels to 17s. It uses 5x100, the same pattern as many other compact Toyotas of the period, with a small 54.1 mm hub.
5x100 bolt pattern · 54.1 mm centre bore · Stock wheels: 15 × 6, 16 × 6.5, 17 × 7 inch · Stock tyres: 195/65 R15, 205/55 R16, 215/45 R17
Updated 2026-10-31 · High source confidence. Check your exact trim and market. How we check specs
Quick specs
| Specification | Value |
|---|---|
| Bolt pattern | |
| Stock tyre sizes | |
| Centre bore | 54.1 mm |
| Fastener and thread | Wheel nut, M12x1.5 |
| Tightening torque | Confirm in your handbook |
Stock wheels and tyres
Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.
| Trim | Axle | Wheel | Tyre |
|---|---|---|---|
| Standard / LE, 15-inch | Front and rear | 15 × 6 inch, ET33 | 195/65 R15 |
| S and 16-inch grades | Front and rear | 16 × 6.5 inch, ET39 | 205/55 R16 |
| XRS, 17-inch | Front and rear | 17 × 7 inch, ET39 | 215/45 R17 |
Explained in our guides
Read these before choosing wheels for the Corolla: they explain the offset, fitment and hub numbers in this guide.
- Wheel offset explained: choosing ET without guessingUnderstand positive and negative wheel offset, calculate inner clearance and outer position, and choose an ET using measurements from your own car.
- Flush, poke and tucked fitment: measure the whole tyreUnderstand flush, poked and tucked wheels, calculate how width and offset change the look, and check clearance beyond a parked side-on photograph.
- Hub-centric vs lug-centric wheels: choosing hub ringsLearn what hub rings do, how to specify their inner and outer diameters, and why centring, wheel seats and vibration need separate checks.
Popular community setups
Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.
Width and offset guidance
Offset range
Check the exact setup
There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.
Common width limit
Measure before ordering
A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.
These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.
Clearance notes
- The same ToyotaNation owner advises against ET20 on a 17x8 because it would stick out too far.
- Factory offsets are ET33 on the 15-inch wheel and ET39 on the 16 and 17-inch wheels. The owner 17x8 ET35 sits about 17 mm further out and 9 mm further in than the XRS 17x7 ET39.
- The hub bore is 54.1 mm and the wheel nuts are M12x1.5. Most aftermarket wheels have a larger bore and need hub-centric rings.
- We have not confirmed a factory wheel-nut torque for this generation. Use the figure in the owner's handbook.
- Check full steering lock and suspension travel with the car loaded. Match wheel load rating, tyre load and speed ratings, fastener seats and brake clearance.
See it on your car.
Upload a photo and start with a look that suits the Corolla. Try the wheels, colour and stance before you spend on parts.
An AI preview shows the look. It cannot verify physical fitment.
Run the numbers
These tools start with the Standard / LE, 15-inch front size. Choose your own trim or axle in the calculator if it differs.
Questions
What is the bolt pattern of the 2009–2013 Corolla?
5x100, with a 54.1 mm centre bore and M12x1.5 wheel nuts.
What size are the factory wheels?
15x6 ET33 with 195/65 R15, 16x6.5 ET39 with 205/55 R16, and 17x7 ET39 with 215/45 R17 on the XRS.
Can I fit 17-inch wheels to a Corolla that came on 15s?
Yes. The XRS used 17x7 ET39 with 215/45 R17, which is within about 1.5% of the 15-inch tyre's diameter, and owners also run 17x8 ET35 with 225/45 R17.
What size tyres does the Toyota Corolla E140 (North America) have?
Factory tyre (tire) sizes for the 2009–2013 Toyota Corolla E140 (North America) are 195/65 R15, 205/55 R16 and 215/45 R17, depending on trim. Your tyre placard shows the size for your car.
What wheel size does the Toyota Corolla E140 (North America) use?
Factory wheels are 15 × 6 inch, 16 × 6.5 inch and 17 × 7 inch, depending on trim. The stock table lists the offset for each.
What is the Toyota Corolla E140 (North America) centre bore?
54.1 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.
Specs checked against
- Wheel-Size: 2009 Corolla E140 OE sizes, bore and thread
- Wheel-Size: 2011 Corolla E140 OE sizes
- TireWheelGuide: 2010 Corolla sizes, bore and thread
- ToyotaNation: 17x8 with 225/45 R17 on a 10th-gen Corolla
This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.
Related cars
More guides from Toyota or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.