2019–present · saloon
Every Taycan saloon runs a staggered set, with factory wheels in 19, 20 and 21-inch sizes and much wider rims at the back. Owners changing wheels mostly stay at 21 inches on the factory tyre sizes and choose a lower offset so the wheels sit flusher with the arches, often alongside lowering links on air-suspended cars.
5x130 bolt pattern · 71.6 mm centre bore · Stock wheels: 19 × 8, 19 × 10, 20 × 9, 20 × 11, 21 × 9.5, 21 × 11.5 inch · Stock tyres: 225/55 R19, 275/45 R19, 245/45 R20, 285/40 R20, 265/35 R21, 305/30 R21
Updated 2026-10-31 · High source confidence. Check your exact trim and market. How we check specs
| Specification | Value |
|---|---|
| Bolt pattern | |
| Stock tyre sizes | |
| Centre bore | 71.6 mm |
| Fastener and thread | Wheel bolt, M14x1.5 |
| Tightening torque | 160 Nm (confirm in your handbook) |
Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.
| Trim | Axle | Wheel | Tyre |
|---|---|---|---|
| Taycan, 4 and 4S, 19-inch Aero | Front | 19 × 8 inch, ET50 | 225/55 R19 |
| Taycan, 4 and 4S, 19-inch Aero | Rear | 19 × 10 inch, ET47 | 275/45 R19 |
| 20-inch sets, including GTS and Turbo | Front | 20 × 9 inch, ET54 | 245/45 R20 |
| 20-inch sets, including GTS and Turbo | Rear | 20 × 11 inch, ET60 | 285/40 R20 |
| 21-inch sets, including Turbo S | Front | 21 × 9.5 inch, ET60 | 265/35 R21 |
| 21-inch sets, including Turbo S | Rear | 21 × 11.5 inch, ET66 | 305/30 R21 |
Read these before choosing wheels for the Taycan: they explain the offset, fitment and hub numbers in this guide.
Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.
A Taycan Turbo owner on TaycanForum had BC Forged build 21-inch wheels at the factory 21-inch widths and tyre sizes, with offsets chosen to match the 15 mm spacers they had run on the factory 20s. They measured caliper clearance using templates from BC Forged before ordering.
A TaycanForum member posted this size on VR forged wheels with Vivid Racing lowering links. Other members in the thread put the usual range at 14 to 18 mm further out than stock at the front and 12 to 15 mm at the rear.
A Taycan Turbo owner on TaycanForum reported that Vossen recommended these offsets for its 21-inch wheel, about 10 mm further out at the front and 8 mm at the rear than the factory 21s.
Check the exact setup
There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.
Measure before ordering
A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.
These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.
Upload a photo and start with a look that suits the Taycan. Try the wheels, colour and stance before you spend on parts.
An AI preview shows the look. It cannot verify physical fitment.
These tools start with the Taycan, 4 and 4S, 19-inch Aero front size. Choose your own trim or axle in the calculator if it differs.
5x130, with a 71.6 mm centre bore and M14x1.5 wheel bolts torqued to 160 Nm.
21x9.5 ET60 at the front with 265/35 R21 tyres, and 21x11.5 ET66 at the rear with 305/30 R21 tyres.
Owners on TaycanForum commonly run ET45 to ET50 at the front and ET51 to ET58 at the rear on the factory 9.5 and 11.5-inch widths, keeping the factory tyre sizes.
Not the factory 19-inch Aero wheels. The Turbo, Turbo S and GTS are listed on 20 and 21-inch wheels, so check the wheel maker's brake clearance before fitting anything smaller.
Factory tyre (tire) sizes for the 2019–present Porsche Taycan Y1A are 225/55 R19, 275/45 R19, 245/45 R20, 285/40 R20, 265/35 R21 and 305/30 R21, depending on trim, with wider rears on staggered setups. Your tyre placard shows the size for your car.
71.6 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.
160 Nm (about 118 lb-ft) for the original bolts. Confirm in your handbook, especially with aftermarket wheels or bolts.
This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.
More guides from Porsche or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.