17-inch lowered street
- Front and rear
- 17 × 7 inch, ET38 · 215/45 R17
A 2014 Versa S owner on Nissan Versa Forums reports 17x7 ET38 4x100 wheels with 215/45 R17 tyres, a drop of about 2 inches and no rubbing. The car was also used for autocross.
2011–2019 · saloon
Nissan Almera / Versa sedan N17 wheel fitment
The N17 saloon was sold as the Versa in the Americas, the Almera in South-East Asia and Australia, and the Sunny in China, India and the Middle East. It is a budget commuter, so most owners stay on 15- or 16-inch wheels, and the few who modify them usually go to a 16- or 17-inch alloy with a small drop. It uses a four-stud 4x100 hub, which is different from the first-generation Versa.
4x100 bolt pattern · 60.1 mm centre bore · Stock wheels: 15 × 5.5, 16 × 6, 14 × 5.5 inch · Stock tyres: 185/65 R15, 195/55 R16, 175/70 R14
Updated 2026-10-26 · Medium source confidence. Check your exact trim and market. How we check specs
Quick specs
| Specification | Value |
|---|---|
| Bolt pattern | |
| Stock tyre sizes | |
| Centre bore | 60.1 mm |
| Fastener and thread | Wheel nut, M12x1.25 |
| Tightening torque | 113 Nm (confirm in your handbook) |
Stock wheels and tyres
Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.
| Trim | Axle | Wheel | Tyre |
|---|---|---|---|
| US Versa S / S Plus / SV, 15-inch steel | Front and rear | 15 × 5.5 inch, ET40 | 185/65 R15 |
| US Versa SL from 2014, 16-inch alloy | Front and rear | 16 × 6 inch, ET45 | 195/55 R16 |
| South-East Asian Almera 1.2 base, 14-inch | Front and rear | 14 × 5.5 inch, ET40 | 175/70 R14 |
Explained in our guides
Read these before choosing wheels for the Almera / Versa sedan: they explain the offset, fitment and hub numbers in this guide.
- Wheel offset explained: choosing ET without guessingUnderstand positive and negative wheel offset, calculate inner clearance and outer position, and choose an ET using measurements from your own car.
- Flush, poke and tucked fitment: measure the whole tyreUnderstand flush, poked and tucked wheels, calculate how width and offset change the look, and check clearance beyond a parked side-on photograph.
- Hub-centric vs lug-centric wheels: choosing hub ringsLearn what hub rings do, how to specify their inner and outer diameters, and why centring, wheel seats and vibration need separate checks.
Popular community setups
Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.
Conservative 16-inch on coilovers
- Front and rear
- 16 × 7 inch, ET50
A 2015 Versa S owner on Nissan Versa Forums fitted Work Euroline DH 16x7 ET50 wheels with coilovers. He picked a high offset because the arches have little room. No tyre size was given.
Width and offset guidance
Offset range
Check the exact setup
There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.
Common width limit
Measure before ordering
A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.
These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.
Clearance notes
- Only the N17 saloon uses 4x100. The first-generation Versa (C11), including the 2012 US hatchback sold alongside the new saloon, is 4x114.3 with a 66.1 mm bore. Count the studs and check the year and body before buying wheels.
- Most sources give a 60.1 mm hub bore, but one lug-nut database lists 59.1 mm. Measure the hub or use hub-centric rings sized for your car when a wheel's bore is larger.
- The Russian-market Almera sold from 2013 to 2018 is the G15, a different car from the N17. Don't use this guide for it.
- The front arches have little spare room. In the forum's sedan thread, an owner lowered about 4 inches reported rubbing on 17x7.5 ET42 wheels, while a 2-inch drop on 17x7 ET38 cleared.
- In Mexico and parts of Latin America, the N17 was later sold as the V-Drive. Check the hub on those cars against the N17 figures here.
- Check full steering lock and suspension travel with the car loaded. Match wheel load rating, tyre load and speed ratings, fastener seats and brake clearance.
See it on your car.
Upload a photo and start with a look that suits the Almera / Versa sedan. Try the wheels, colour and stance before you spend on parts.
An AI preview shows the look. It cannot verify physical fitment.
Run the numbers
These tools start with the US Versa S / S Plus / SV, 15-inch steel front size. Choose your own trim or axle in the calculator if it differs.
Questions
What is the Nissan Versa sedan bolt pattern for 2012–2019?
4x100, with a 60.1 mm hub bore and M12x1.25 wheel nuts. The older C11 Versa is 4x114.3, so its wheels won't fit.
Are the Almera N17, Versa sedan and Sunny the same for wheels?
They are the same N17 saloon sold under different names, and wheel databases give the same 4x100 hub and 15x5.5 ET40 base wheel in the American, South-East Asian and Australian markets we checked. The Russian Almera G15 is a different car.
What wheel nut torque does the N17 Versa use?
Wheel databases list 113 Nm (about 83 lb-ft).
Will 17-inch wheels fit a Versa sedan?
Yes. An owner runs 17x7 ET38 with 215/45 R17 on a car lowered about 2 inches without rubbing. Much lower offsets or bigger drops are where owners report rubbing.
Can I fit the SL's 16-inch alloys to an S or SV?
Yes. The SL's 16x6 ET45 alloys use the same 4x100 hub, normally with 195/55 R16 tyres.
What size tyres does the Nissan Almera / Versa sedan N17 have?
Factory tyre (tire) sizes for the 2011–2019 Nissan Almera / Versa sedan N17 are 185/65 R15, 195/55 R16 and 175/70 R14, depending on trim. Your tyre placard shows the size for your car.
What wheel size does the Nissan Almera / Versa sedan N17 use?
Factory wheels are 15 × 5.5 inch, 16 × 6 inch and 14 × 5.5 inch, depending on trim. The stock table lists the offset for each.
What is the Nissan Almera / Versa sedan N17 centre bore?
60.1 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.
Specs checked against
- Nissan: 2016 Versa Sedan press kit, wheels and tyres by trim
- Nissan: 2014 Versa Sedan press kit, SL 16-inch wheel change
- TireWheelGuide: 2012 Versa sizes, PCD, bore and thread by generation
- TireWheelGuide: 2015 Versa factory sizes
- Wheel-Size: 2015 Versa factory wheels and offsets
- Wheel-Size: Almera N17 2011–2014 factory sizes
- Wheel-Sizes: Versa lug nut thread and torque
- Nissan Versa Forums: sedan owner wheel setups
- Nissan Versa Forums: 2015 Versa S build with 16x7 wheels
- Nissan Versa Forums: 2014 Versa S autocross build
- Nissan Versa Forums: replacement rims and hub bore
- Wikipedia: Nissan Almera, N17 market names and G15
This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.
Related cars
More guides from Nissan or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.