Wide 20-inch road setup
- Front
- 20 × 10 inch, ET30 · 285/35 R20
- Rear
- 20 × 12 inch, ET20 · 335/30 R20
Rforged FF6 fitment supplied for the R35, without spacers. Have the supplier confirm brake clearance and the tyre pairing for the exact car.
2007–2025 · coupe
Nissan GT-R R35 wheel fitment
The R35 uses staggered wheels and tyres, with substantially wider rears. Wider 20-inch forged wheels are common, but the brake package and matching tyre circumferences are central to fitment.
5x114.3 bolt pattern · 66.1 mm centre bore · Stock wheels: 20 × 9.5, 20 × 10.5, 20 × 10 inch · Stock tyres: 255/40 R20, 285/35 R20
Updated 2026-10-04 · Medium source confidence. Check your exact trim and market. How we check specs
Quick specs
| Specification | Value |
|---|---|
| Bolt pattern | |
| Stock tyre sizes | |
| Centre bore | 66.1 mm |
| Fastener and thread | Wheel nut, thread not confirmed |
| Tightening torque | Confirm in your handbook |
Stock wheels and tyres
Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.
| Trim | Axle | Wheel | Tyre |
|---|---|---|---|
| Standard / Premium | Front | 20 × 9.5 inch, ET45 | 255/40 R20 |
| Standard / Premium | Rear | 20 × 10.5 inch, ET25 | 285/35 R20 |
| Nismo and later Track Edition with 10J front wheels | Front | 20 × 10 inch, ET41 | 255/40 R20 |
| Nismo and later Track Edition with 10J front wheels | Rear | 20 × 10.5 inch, ET25 | 285/35 R20 |
Explained in our guides
Read these before choosing wheels for the GT-R: they explain the offset, fitment and hub numbers in this guide.
- Wheel offset explained: choosing ET without guessingUnderstand positive and negative wheel offset, calculate inner clearance and outer position, and choose an ET using measurements from your own car.
- Flush, poke and tucked fitment: measure the whole tyreUnderstand flush, poked and tucked wheels, calculate how width and offset change the look, and check clearance beyond a parked side-on photograph.
- Staggered vs square wheels: tyres, rotation and AWDCompare square and staggered wheel setups, calculate front-to-rear tyre diameter, and understand rotation limits and all-wheel-drive requirements.
Popular community setups
Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.
20-inch customer fitment
- Front
- 20 × 10 inch, ET35
- Rear
- 20 × 11 inch, ET5
LF Industries documents this customer wheel combination. Tyre sizes and suspension changes were not specified, so this is a wheel reference rather than a complete fitment prescription.
Width and offset guidance
Offset range
Check the exact setup
There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.
Common width limit
Measure before ordering
A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.
These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.
Clearance notes
- Standard steel-brake cars use M12x1.25 nuts and 132 Nm. Carbon-ceramic Nismo and T-spec variants use M14x1.5 hardware; the 2024 Nissan manual specifies 155 Nm for Nismo, Nismo Special Edition and T-spec. Identify the brake and hub package before ordering nuts.
- Generic R35 charts quoting 132 Nm omit the later exceptions. The manufacturer values above take precedence; a single generation-wide thread or torque value would be misleading.
- The all-wheel-drive system requires a suitable front-to-rear rolling-circumference relationship. Confirm actual tyre specifications, not just nominal widths.
- Nissan ended R35 production in August 2025. Earlier Track Edition packages differ, so the 10J stock entry applies only to cars supplied with that wheel.
- Check full steering lock and suspension travel with the car loaded. Match wheel load rating, tyre load and speed ratings, fastener seats and brake clearance.
See it on your car.
Upload a photo and start with a look that suits the GT-R. Try the wheels, colour and stance before you spend on parts.
An AI preview shows the look. It cannot verify physical fitment.
Run the numbers
These tools start with the Standard / Premium front size. Choose your own trim or axle in the calculator if it differs.
Questions
What is the R35 GT-R bolt pattern?
It is 5x114.3 with a 66.1 mm centre bore.
Do all R35 GT-Rs use the same wheel nuts?
No. Standard cars use M12x1.25; carbon-ceramic variants use M14x1.5. Torque also differs, with 132 Nm and 155 Nm applications.
What tyres are fitted to standard R35 wheels?
The factory pairing is 255/40 R20 front and 285/35 R20 rear.
Can I use 12-inch rear wheels?
Yes, documented 20x12 rear fitments exist. Wheel offset, brake clearance and the front-to-rear tyre pairing must all suit the car.
What wheel size does the Nissan GT-R R35 use?
Factory wheels are 20 × 9.5 inch, 20 × 10.5 inch and 20 × 10 inch, depending on trim. The stock table lists the offset for each.
What is the Nissan GT-R R35 centre bore?
66.1 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.
Specs checked against
- Nissan: 2024 GT-R owner manual
- STM: R35 wheel and hardware specifications
- MYG Lab: GT-R matching data
- Speed by Design: Rforged FF6 fitment
- LF Industries: R35 customer fitments
- Nissan: final R35 production announcement
This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.
Related cars
More guides from Nissan or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.