1999–2002 · coupe
The R34 GT-R uses equal wheel and tyre sizes on all four corners. Owners commonly stay with 18-inch wheels, moving from the factory 9J width to 9.5J wheels in either a conservative or lower-offset fitment.
5x114.3 bolt pattern · 66 mm centre bore · Stock wheels: 18 × 9 inch · Stock tyres: 245/40 R18
Updated 2026-10-04 · Medium source confidence. Check your exact trim and market. How we check specs
| Specification | Value |
|---|---|
| Bolt pattern | |
| Stock tyre sizes | |
| Centre bore | 66 mm |
| Fastener and thread | Wheel nut, M12x1.25 |
| Tightening torque | Confirm in your handbook |
Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.
| Trim | Axle | Wheel | Tyre |
|---|---|---|---|
| GT-R / V-spec / N1 | Front and rear | 18 × 9 inch, ET30 | 245/40 R18 |
| V-spec II / M-spec / Nür, standard 18-inch package | Front and rear | 18 × 9 inch, ET30 | 245/40 R18 |
Read these before choosing wheels for the Skyline GT-R: they explain the offset, fitment and hub numbers in this guide.
Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.
BBS lists this wheel specification for the BNR34 and specialist fitment guides use this tyre size. Check the wheel's Brembo clearance and the arches at the intended ride height.
Nismo explicitly lists 9.5J ET12 for the BNR34, with this reference tyre size confirmed by its retailer and owner examples. The lower offset needs careful arch and camber checks on lowered cars.
Check the exact setup
There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.
Measure before ordering
A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.
These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.
Upload a photo and start with a look that suits the Skyline GT-R. Try the wheels, colour and stance before you spend on parts.
An AI preview shows the look. It cannot verify physical fitment.
These tools start with the GT-R / V-spec / N1 front size. Choose your own trim or axle in the calculator if it differs.
5x114.3, with M12x1.25 wheel nuts. Nissan lists a 66 mm hub hole; the aftermarket commonly describes the fitment as 66.1 mm.
18x9 ET30 with 245/40 R18 tyres on all four corners.
Yes. BBS lists ET30 and Nismo lists ET12 applications. The lower-offset option needs more attention to arch clearance and alignment.
The original setup is square. The listed alternatives also keep matching tyres on all four corners for the four-wheel-drive system.
Factory tyre (tire) sizes for the 1999–2002 Nissan Skyline GT-R R34 / BNR34 are 245/40 R18, depending on trim. Your tyre placard shows the size for your car.
Factory wheels are 18 × 9 inch, depending on trim. The stock table lists the offset for each.
66 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.
This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.
More guides from Nissan or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.