18-inch daily
- Front and rear
- 18 × 8 inch, ET50 · 235/40 R18
BBS SR example on standard suspension with unrolled arches and no reported rubbing.
2018–2022 · hatchback
Hyundai Veloster N JS wheel fitment
Veloster N wheel changes often focus on moving from factory 19s to an 18-inch setup. There is limited space for wide front tyres, so conservative offsets suit road cars better than an aggressive stance.
5x114.3 bolt pattern · 67.1 mm centre bore · Stock wheels: 18 × 7.5, 19 × 8 inch · Stock tyres: 225/40 R18, 235/35 R19
Updated 2026-10-04 · High source confidence. Check your exact trim and market. How we check specs
Quick specs
| Specification | Value |
|---|---|
| Bolt pattern | |
| Stock tyre sizes | |
| Centre bore | 67.1 mm |
| Fastener and thread | Wheel nut, M12x1.5 |
| Tightening torque | Confirm in your handbook |
Stock wheels and tyres
Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.
| Trim | Axle | Wheel | Tyre |
|---|---|---|---|
| Early N without Performance Package | Front and rear | 18 × 7.5 inch, ET53 | 225/40 R18 |
| N Performance Package / later standard performance specification | Front and rear | 19 × 8 inch, ET55 | 235/35 R19 |
Explained in our guides
Read these before choosing wheels for the Veloster N: they explain the offset, fitment and hub numbers in this guide.
- Wheel offset explained: choosing ET without guessingUnderstand positive and negative wheel offset, calculate inner clearance and outer position, and choose an ET using measurements from your own car.
- Flush, poke and tucked fitment: measure the whole tyreUnderstand flush, poked and tucked wheels, calculate how width and offset change the look, and check clearance beyond a parked side-on photograph.
- Hub-centric vs lug-centric wheels: choosing hub ringsLearn what hub rings do, how to specify their inner and outer diameters, and why centring, wheel seats and vibration need separate checks.
Popular community setups
Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.
18-inch wider wheel
- Front and rear
- 18 × 8.5 inch, ET50 · 235/40 R18
Documented Advan GT Beyond fitment. The source does not specify suspension, so check ride-height clearance.
19-inch lowered road setup
- Front and rear
- 19 × 8.5 inch, ET43 · 235/35 R19
Documented Konig Countergram setup with H&R lowering springs.
Width and offset guidance
Offset range
Check the exact setup
There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.
Common width limit
Measure before ordering
A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.
These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.
Clearance notes
- The owner's manual gives 107–127 Nm, rather than one torque value. The single-number torque field is therefore omitted.
- A documented 18x8 ET45 setup with 245/40 R18 tyres rubs the liners during hard driving.
- Lower-offset 8.5-inch wheels can need rolled arches and extra camber. Do not treat an owner's static fit as a guarantee under compression.
- Confirm the wheel clears the Performance Package brakes before buying an 18-inch set.
- Check full steering lock and suspension travel with the car loaded. Match wheel load rating, tyre load and speed ratings, fastener seats and brake clearance.
See it on your car.
Upload a photo and start with a look that suits the Veloster N. Try the wheels, colour and stance before you spend on parts.
An AI preview shows the look. It cannot verify physical fitment.
Run the numbers
These tools start with the Early N without Performance Package front size. Choose your own trim or axle in the calculator if it differs.
Questions
What is the Veloster N bolt pattern?
5x114.3 with a 67.1 mm hub bore and M12x1.5 nuts.
Can the Veloster N use 18-inch wheels?
Yes. There are documented 18x8 ET50 and 18x8.5 ET50 setups, but brake clearance remains specific to the wheel.
Will 245/40 R18 tyres rub?
They can. One documented 18x8 ET45 setup rubs the liners under hard driving, so check the exact tyre, offset and suspension.
What size tyres does the Hyundai Veloster N JS have?
Factory tyre (tire) sizes for the 2018–2022 Hyundai Veloster N JS are 225/40 R18 and 235/35 R19, depending on trim. Your tyre placard shows the size for your car.
What wheel size does the Hyundai Veloster N JS use?
Factory wheels are 18 × 7.5 inch and 19 × 8 inch, depending on trim. The stock table lists the offset for each.
What is the Hyundai Veloster N JS centre bore?
67.1 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.
Specs checked against
- Hyundai Veloster N owner's manual
- Hyundai Veloster N factory brochure
- Veloster N wheel hardware reference
- TireWheelGuide Veloster N factory sizes
- ThreePiece installed Veloster N examples
This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.
Related cars
More guides from Hyundai or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.