18-inch daily and track
- Front and rear
- 18 × 8.5 inch, ET45 · 245/40 R18
Widely documented on standard suspension. Confirm the chosen wheel clears the N calipers.
2021–present · saloon
Hyundai Elantra N CN7 wheel fitment
Elantra N owners commonly replace the factory 19-inch wheels with 18-inch sets for road and track use. Moderate offsets are popular because pushing the front tyres too far out can cause contact during hard cornering.
5x114.3 bolt pattern · 67.1 mm centre bore · Stock wheels: 19 × 8 inch · Stock tyres: 245/35 R19
Updated 2026-10-04 · High source confidence. Check your exact trim and market. How we check specs
Quick specs
| Specification | Value |
|---|---|
| Bolt pattern | |
| Stock tyre sizes | |
| Centre bore | 67.1 mm |
| Fastener and thread | Wheel nut, M12x1.5 |
| Tightening torque | Confirm in your handbook |
Stock wheels and tyres
Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.
| Trim | Axle | Wheel | Tyre |
|---|---|---|---|
| N manual / DCT, including facelift forged 19-inch wheels | Front and rear | 19 × 8 inch, ET55 | 245/35 R19 |
Explained in our guides
Read these before choosing wheels for the Elantra N: they explain the offset, fitment and hub numbers in this guide.
- Wheel offset explained: choosing ET without guessingUnderstand positive and negative wheel offset, calculate inner clearance and outer position, and choose an ET using measurements from your own car.
- Flush, poke and tucked fitment: measure the whole tyreUnderstand flush, poked and tucked wheels, calculate how width and offset change the look, and check clearance beyond a parked side-on photograph.
- Hub-centric vs lug-centric wheels: choosing hub ringsLearn what hub rings do, how to specify their inner and outer diameters, and why centring, wheel seats and vibration need separate checks.
Popular community setups
Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.
19-inch wider road setup
- Front and rear
- 19 × 8.5 inch, ET40 · 245/35 R19
N-cars owners describe this as close to flush. Check clearance under compression, especially when lowered; lower offsets have rubbed during autocross.
Width and offset guidance
Offset range
Check the exact setup
There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.
Common width limit
Measure before ordering
A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.
These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.
Clearance notes
- Hyundai specifies 107–127 Nm in the owner's manual. The torque field is omitted because the schema only accepts one number.
- This is the full N model, not the Elantra N Line. Brake clearance must be checked for the N.
- Lower offsets around ET35–38 need more caution than ET45, particularly with wider tyres or track use.
- Check full steering lock and suspension travel with the car loaded. Match wheel load rating, tyre load and speed ratings, fastener seats and brake clearance.
See it on your car.
Upload a photo and start with a look that suits the Elantra N. Try the wheels, colour and stance before you spend on parts.
An AI preview shows the look. It cannot verify physical fitment.
Run the numbers
These tools start with the N manual / DCT, including facelift forged 19-inch wheels front size. Choose your own trim or axle in the calculator if it differs.
Questions
What is the Elantra N bolt pattern?
5x114.3, with a 67.1 mm centre bore and M12x1.5 nuts.
What 18-inch tyre size replaces the factory 19s?
245/40 R18 on 18x8.5 ET45 wheels is a commonly documented combination.
Do 19x8.5 ET35 wheels fit without rubbing?
Some owners run them, but outward tyre position and reports of rubbing on similarly low offsets make this unsuitable as a universal no-rub recommendation.
What wheel size does the Hyundai Elantra N CN7 use?
Factory wheels are 19 × 8 inch, depending on trim. The stock table lists the offset for each.
What is the Hyundai Elantra N CN7 centre bore?
67.1 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.
Specs checked against
- Hyundai Elantra N owner's manual
- Limitless Tire N hardware and torque
- LFI CN7 hardware guide
- TireWheelGuide Elantra N factory dimensions
- Custom Offsets installed Elantra N examples
- N-cars Elantra N fitment reports
- Konig Elantra N fitment guide
This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.
Related cars
More guides from Hyundai or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.