Lightweight daily 17-inch
- Front and rear
- 17 × 7 inch, ET40 · 205/45 R17
OZ Racing application listed for the R56. Order the version approved for the fitted Cooper S or JCW brakes.
2006–2013 · hatchback
MINI Cooper S / John Cooper Works R56 wheel fitment
The R56 is commonly fitted with light 17-inch wheels for road and track use. Its four-bolt hubs and JCW brake clearance make wheel choice more specific than the diameter alone suggests.
4x100 bolt pattern · 56.1 mm centre bore · Stock wheels: 16 × 6.5, 17 × 7, 18 × 7 inch · Stock tyres: 195/55 R16, 205/45 R17, 205/40 R18
Updated 2026-10-04 · High source confidence. Check your exact trim and market. How we check specs
Quick specs
| Specification | Value |
|---|---|
| Bolt pattern | |
| Stock tyre sizes | |
| Centre bore | 56.1 mm |
| Fastener and thread | Wheel bolt, M14x1.25 |
| Tightening torque | 140 Nm (confirm in your handbook) |
Stock wheels and tyres
Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.
| Trim | Axle | Wheel | Tyre |
|---|---|---|---|
| Cooper S, standard 16-inch | Front and rear | 16 × 6.5 inch, ET48 | 195/55 R16 |
| Cooper S option / JCW, 17-inch | Front and rear | 17 × 7 inch, ET48 | 205/45 R17 |
| JCW accessory 18-inch | Front and rear | 18 × 7 inch, ET52 | 205/40 R18 |
Explained in our guides
Read these before choosing wheels for the Cooper S / John Cooper Works: they explain the offset, fitment and hub numbers in this guide.
- Wheel offset explained: choosing ET without guessingUnderstand positive and negative wheel offset, calculate inner clearance and outer position, and choose an ET using measurements from your own car.
- Flush, poke and tucked fitment: measure the whole tyreUnderstand flush, poked and tucked wheels, calculate how width and offset change the look, and check clearance beyond a parked side-on photograph.
- Hub-centric vs lug-centric wheels: choosing hub ringsLearn what hub rings do, how to specify their inner and outer diameters, and why centring, wheel seats and vibration need separate checks.
Popular community setups
Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.
Wider road setup
- Front and rear
- 17 × 8 inch, ET40 · 215/40 R17
A documented R56/JCW build size. Check arch and liner clearance on lowered cars and obtain a JCW brake-clearance confirmation.
Width and offset guidance
Offset range
Check the exact setup
There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.
Common width limit
Measure before ordering
A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.
These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.
Clearance notes
- The R56 uses M14x1.25 bolts. Do not use the M12x1.5 specification of earlier MINI applications.
- The workshop specification is 140 Nm for the M14 bolts; 120 Nm references commonly concern the earlier M12 hardware.
- A 4x100 wheel intended for another car may have bolt holes too small for the R56 M14 bolts.
- JCW and GP brake packages require wheel-specific clearance checks. The GP is not covered by the regular JCW factory rows.
- Check full steering lock and suspension travel with the car loaded. Match wheel load rating, tyre load and speed ratings, fastener seats and brake clearance.
See it on your car.
Upload a photo and start with a look that suits the Cooper S / John Cooper Works. Try the wheels, colour and stance before you spend on parts.
An AI preview shows the look. It cannot verify physical fitment.
Run the numbers
These tools start with the Cooper S, standard 16-inch front size. Choose your own trim or axle in the calculator if it differs.
Questions
What is the R56 Cooper S bolt pattern?
4x100 with a 56.1 mm centre bore.
Does the R56 use M12 wheel bolts?
No. Its factory bolts are M14x1.25, with a nominal tightening torque of 140 Nm.
Will every 17-inch wheel clear JCW brakes?
No. The barrel and spoke shape must be approved for the JCW brake package.
What tyres fit the standard 17-inch R56 wheels?
205/45 R17 is the factory size on 17x7 ET48 wheels.
What wheel size does the MINI Cooper S / John Cooper Works R56 use?
Factory wheels are 16 × 6.5 inch, 17 × 7 inch and 18 × 7 inch, depending on trim. The stock table lists the offset for each.
What is the MINI Cooper S / John Cooper Works R56 centre bore?
56.1 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.
What is the MINI Cooper S / John Cooper Works R56 wheel bolt torque?
140 Nm (about 103 lb-ft) for the original bolts. Confirm in your handbook, especially with aftermarket wheels or bolts.
Specs checked against
- Alloy Wheels Direct: MINI wheel chart
- MINI workshop manual: M14 bolts and 140 Nm
- MINI2: R56 wheel torque discussion
- BONOSS: R56 hub and bolt dimensions
- Autex MINI wheel application catalogue
- LFI: recorded R56 wheel setups
This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.
Related cars
More guides from MINI or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.