19-inch road stagger
- Front
- 19 × 8.5 inch, ET35 · 235/40 R19
- Rear
- 19 × 9.5 inch, ET40 · 265/35 R19
Documented Vertini RFS1.9 setup. Verify spoke clearance over the GT Brembos and rolling circumference on AWD cars.
2017–2023 · fastback
Kia Stinger GT CK wheel fitment
The Stinger GT comes with staggered wheels and tyres. Common changes retain that layout while increasing wheel width, with particular attention to Brembo caliper clearance.
5x114.3 bolt pattern · 67.1 mm centre bore · Stock wheels: 19 × 8, 19 × 8.5 inch · Stock tyres: 225/40 R19, 255/35 R19
Updated 2026-10-04 · High source confidence. Check your exact trim and market. How we check specs
Quick specs
| Specification | Value |
|---|---|
| Bolt pattern | |
| Stock tyre sizes | |
| Centre bore | 67.1 mm |
| Fastener and thread | Wheel nut, M12x1.5 |
| Tightening torque | Confirm in your handbook |
Stock wheels and tyres
Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.
| Trim | Axle | Wheel | Tyre |
|---|---|---|---|
| 3.3 GT / GT1 / GT2 19-inch staggered package | Front | 19 × 8 inch, ET34 | 225/40 R19 |
| 3.3 GT / GT1 / GT2 19-inch staggered package | Rear | 19 × 8.5 inch, ET46.5 | 255/35 R19 |
Explained in our guides
Read these before choosing wheels for the Stinger GT: they explain the offset, fitment and hub numbers in this guide.
- Wheel offset explained: choosing ET without guessingUnderstand positive and negative wheel offset, calculate inner clearance and outer position, and choose an ET using measurements from your own car.
- Flush, poke and tucked fitment: measure the whole tyreUnderstand flush, poked and tucked wheels, calculate how width and offset change the look, and check clearance beyond a parked side-on photograph.
- Staggered vs square wheels: tyres, rotation and AWDCompare square and staggered wheel setups, calculate front-to-rear tyre diameter, and understand rotation limits and all-wheel-drive requirements.
Popular community setups
Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.
20-inch stagger
- Front
- 20 × 9 inch, ET32 · 245/35 R20
- Rear
- 20 × 10.5 inch, ET45 · 285/30 R20
Documented Stance SF-07 setup. Suspension details were not supplied, so check compression clearance before lowering.
20-inch square
- Front and rear
- 20 × 9 inch, ET35 · 245/35 R20
Documented Rohana RFX13 setup on Eibach springs; equal sizes allow front-to-rear tyre rotation.
Width and offset guidance
Offset range
Check the exact setup
There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.
Common width limit
Measure before ordering
A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.
These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.
Clearance notes
- Kia's owner's manual specifies 107–127 Nm. A fitment database lists 130 Nm; the manufacturer range takes precedence and is retained here instead of a scalar torque value.
- Selected 18-inch wheels can clear the GT Brembos. The ThreePiece guide's blanket 19-inch minimum conflicts with owners' documented 18-inch fitments.
- Front and rear tyre rolling circumferences must remain suitably matched on AWD cars.
- Factory entries cover the confirmed GT staggered package. Market-specific square winter and other optional packages are not listed.
- Check full steering lock and suspension travel with the car loaded. Match wheel load rating, tyre load and speed ratings, fastener seats and brake clearance.
See it on your car.
Upload a photo and start with a look that suits the Stinger GT. Try the wheels, colour and stance before you spend on parts.
An AI preview shows the look. It cannot verify physical fitment.
Run the numbers
These tools start with the 3.3 GT / GT1 / GT2 19-inch staggered package front size. Choose your own trim or axle in the calculator if it differs.
Questions
What is the Stinger GT bolt pattern?
5x114.3 with a 67.1 mm hub bore and M12x1.5 nuts.
Can 18-inch wheels clear Stinger GT Brembos?
Some can. Use a confirmed GT fitment or a brake template because barrel and spoke shape determine clearance.
Are Stinger GT factory wheels staggered?
The common 19-inch GT package uses 19x8 ET34 fronts and 19x8.5 ET46.5 rears, with 225/40 R19 and 255/35 R19 tyres.
What size tyres does the Kia Stinger GT CK have?
Factory tyre (tire) sizes for the 2017–2023 Kia Stinger GT CK are 225/40 R19 and 255/35 R19, depending on trim, with wider rears on staggered setups. Your tyre placard shows the size for your car.
What wheel size does the Kia Stinger GT CK use?
Factory wheels are 19 × 8 inch and 19 × 8.5 inch, depending on trim. The stock table lists the offset for each.
What is the Kia Stinger GT CK centre bore?
67.1 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.
Specs checked against
- Kia Stinger factory technical specification
- Kia Stinger owner's manual, wheel torque
- Element Wheels Stinger GT hardware
- ThreePiece Stinger wheel examples
- Stinger owners: factory offsets
- Stinger owners: 18-inch Brembo clearance
- WheelFitment conflicting torque reference
This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.
Related cars
More guides from Kia or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.