Mild 18-inch daily setup
- Front and rear
- 18 × 8.5 inch, ET45 · 235/40 R18
Within the retailer’s documented daily fitment choices. Suitable wheel designs can work at standard height or on mild springs; inspect the front liner tab after lowering.
2016–2021 · saloon / coupe / hatchback
Honda Civic 10th gen (FC / FK), non-Type R wheel fitment
The tenth-generation Civic commonly runs 18-inch aftermarket wheels for daily and lowered builds. This guide includes the Si but excludes the FK8 Type R, which has a different bolt pattern and wheel hardware.
5x114.3 bolt pattern · 64.1 mm centre bore · Stock wheels: 16 × 7, 17 × 7, 18 × 8 inch · Stock tyres: 215/55 R16, 215/50 R17, 235/40 R18
Updated 2026-10-04 · High source confidence. Check your exact trim and market. How we check specs
Quick specs
| Specification | Value |
|---|---|
| Bolt pattern | |
| Stock tyre sizes | |
| Centre bore | 64.1 mm |
| Fastener and thread | Wheel nut, M12x1.5 |
| Tightening torque | 108 Nm (confirm in your handbook) |
Stock wheels and tyres
Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.
| Trim | Axle | Wheel | Tyre |
|---|---|---|---|
| US LX saloon / coupe | Front and rear | 16 × 7 inch, ET45 | 215/55 R16 |
| US EX / EX-T / EX-L / Touring, 17-inch package | Front and rear | 17 × 7 inch, ET45 | 215/50 R17 |
| US Sport / Sport Touring hatchback | Front and rear | 18 × 8 inch, ET50 | 235/40 R18 |
| US Si saloon / coupe, 2017–2020 | Front and rear | 18 × 8 inch, ET50 | 235/40 R18 |
Explained in our guides
Read these before choosing wheels for the Civic: they explain the offset, fitment and hub numbers in this guide.
- Wheel offset explained: choosing ET without guessingUnderstand positive and negative wheel offset, calculate inner clearance and outer position, and choose an ET using measurements from your own car.
- Flush, poke and tucked fitment: measure the whole tyreUnderstand flush, poked and tucked wheels, calculate how width and offset change the look, and check clearance beyond a parked side-on photograph.
- Hub-centric vs lug-centric wheels: choosing hub ringsLearn what hub rings do, how to specify their inner and outer diameters, and why centring, wheel seats and vibration need separate checks.
Popular community setups
Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.
Flush lowered setup
- Front and rear
- 18 × 9.5 inch, ET38 · 235/40 R18
Documented with Enkei RPF1 wheels and Eibach Pro-Kit springs. Check the tyre maker’s permitted rim widths and liner clearance; a lower ride height or wider tyre can need further arch work.
Width and offset guidance
Offset range
Check the exact setup
There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.
Common width limit
Measure before ordering
A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.
These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.
Clearance notes
- Factory Honda nuts use a rounded seat. Most aftermarket wheels need their own conical-seat M12x1.5 nuts; match the wheel manufacturer’s specification.
- The FK8 Type R uses 5x120 and M14x1.5 hardware and is not covered by this file.
- The factory rows describe US packages. European hatchback trim names and tyre packages differ, so use the vehicle placard for the original tyre size.
- Lowering can bring the tyre into contact with the front wheelarch liner tab. Clearance also changes with tyre shoulder shape and alignment.
- The 108 Nm figure is the Honda factory wheel installation value.
- Check full steering lock and suspension travel with the car loaded. Match wheel load rating, tyre load and speed ratings, fastener seats and brake clearance.
See it on your car.
Upload a photo and start with a look that suits the Civic. Try the wheels, colour and stance before you spend on parts.
An AI preview shows the look. It cannot verify physical fitment.
Run the numbers
These tools start with the US LX saloon / coupe front size. Choose your own trim or axle in the calculator if it differs.
Questions
What is the bolt pattern of a non-Type R tenth-generation Civic?
It is 5x114.3 with a 64.1 mm centre bore and M12x1.5 wheel nuts, including the Si.
Will FK8 Type R wheels bolt onto a Civic Sport or Si?
No. The Type R uses a different 5x120 bolt pattern.
What tyre size is commonly used on 18x8.5 wheels?
235/40 R18 is a documented daily choice. Confirm the tyre’s approved rim range and clearance for the chosen offset and ride height.
What torque do Civic wheel nuts need?
Honda specifies 108 Nm for the factory installation.
What wheel size does the Honda Civic 10th gen (FC / FK), non-Type R use?
Factory wheels are 16 × 7 inch, 17 × 7 inch and 18 × 8 inch, depending on trim. The stock table lists the offset for each.
What is the Honda Civic 10th gen (FC / FK), non-Type R centre bore?
64.1 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.
Specs checked against
- Honda: Civic alloy wheel installation instructions
- Limitless Tire: 2017 Civic mounting and torque data
- TireWheelGuide: Civic FC factory fitments
- Custom Offsets: tenth-generation Civic factory and owner setups
This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.
Related cars
More guides from Honda or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.