19-inch square daily
- Front and rear
- 19 × 9 inch, ET30 · 255/40 R19
TSW Bathurst wheels on a 2017 Premium AWD, shown in the InfinitiQ60.org aftermarket wheel picture thread. Keeps the factory tyre size and sits 10 mm further out than stock.
2017–2022 · coupe
Infiniti Q60 CV37 wheel fitment
The second-generation Q60 coupe sits on the same hub specification as the Q50, and owners usually move to wider 19 or 20-inch wheels to fill the arches. Rear-wheel-drive Red Sport 400s left the factory on staggered 20s, so many owners keep a staggered setup, while AWD cars generally stay square.
5x114.3 bolt pattern · 66.1 mm centre bore · Stock wheels: 19 × 9, 19 × 9.5, 20 × 9, 20 × 9.5 inch · Stock tyres: 255/40 R19, 245/40 R19, 265/35 R19, 255/35 R20, 275/30 R20
Updated 2026-10-26 · Medium source confidence. Check your exact trim and market. How we check specs
Quick specs
| Specification | Value |
|---|---|
| Bolt pattern | |
| Stock tyre sizes | |
| Centre bore | 66.1 mm |
| Fastener and thread | Wheel nut, M12x1.25 |
| Tightening torque | 108 Nm (confirm in your handbook) |
Stock wheels and tyres
Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.
| Trim | Axle | Wheel | Tyre |
|---|---|---|---|
| 2.0t / 3.0t (Pure, Premium, Luxe, Sport), 19-inch | Front and rear | 19 × 9 inch, ET40 | 255/40 R19 |
| 2017 2.0t / 3.0t Premium, 19-inch all-season option | Front and rear | 19 × 9 inch, ET40 | 245/40 R19 |
| 2017 Red Sport 400 RWD, staggered 19-inch | Front | 19 × 9 inch, ET37 | 245/40 R19 |
| 2017 Red Sport 400 RWD, staggered 19-inch | Rear | 19 × 9.5 inch, ET44 | 265/35 R19 |
| 2018–2022 Red Sport 400 RWD, staggered 20-inch | Front | 20 × 9 inch, ET40 | 255/35 R20 |
| 2018–2022 Red Sport 400 RWD, staggered 20-inch | Rear | 20 × 9.5 inch, ET47 | 275/30 R20 |
| 2018–2022 Red Sport 400 AWD, square 20-inch | Front and rear | 20 × 9 inch, ET40 | 255/35 R20 |
Explained in our guides
Read these before choosing wheels for the Q60: they explain the offset, fitment and hub numbers in this guide.
- Wheel offset explained: choosing ET without guessingUnderstand positive and negative wheel offset, calculate inner clearance and outer position, and choose an ET using measurements from your own car.
- Flush, poke and tucked fitment: measure the whole tyreUnderstand flush, poked and tucked wheels, calculate how width and offset change the look, and check clearance beyond a parked side-on photograph.
- Staggered vs square wheels: tyres, rotation and AWDCompare square and staggered wheel setups, calculate front-to-rear tyre diameter, and understand rotation limits and all-wheel-drive requirements.
Popular community setups
Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.
19-inch square, lowered
- Front and rear
- 19 × 9.5 inch, ET22 · 245/40 R19
ESR CS8 wheels with RS-R Down lowering springs, posted in the InfinitiQ60.org picture thread. The 245 tyre is slightly stretched on a 9.5-inch rim.
19-inch staggered
- Front
- 19 × 9.5 inch, ET25 · 255/40 R19
- Rear
- 19 × 10.5 inch, ET28 · 285/35 R19
Custom two-piece forged wheels posted in the InfinitiQ60.org picture thread. A staggered setup like this suits rear-wheel-drive cars.
20-inch staggered, near-factory offsets
- Front
- 20 × 9 inch, ET32 · 255/35 R20
- Rear
- 20 × 10.5 inch, ET45 · 285/30 R20
Velgen VMB5 wheels on a rear-wheel-drive car, from the InfinitiQ60.org picture thread. The owner reported that the ET45 rear cleared the brakes.
20-inch staggered, lowered
- Front
- 20 × 9.5 inch, ET20 · 255/35 R20
- Rear
- 20 × 11 inch, ET45 · 295/30 R20
Posted by more than one owner in the InfinitiQ60.org picture thread, including a set of Avant Garde M632s on RS-R Down springs.
20-inch square, coilovers
- Front and rear
- 20 × 10 inch, ET22 · 255/35 R20
Rohana RFX13 wheels on a 2017 Red Sport 400 AWD with BC Racing coilovers, from the InfinitiQ60.org picture thread. The owner said the fitment stuck out too far at standard ride height.
Width and offset guidance
Offset range
Check the exact setup
There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.
Common width limit
Measure before ordering
A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.
These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.
Clearance notes
- Owners note that Red Sport 400 brakes need generous spoke and barrel clearance. Check the specific wheel design, especially below 19 inches.
- On AWD cars, keep front and rear tyre diameters matched. Factory AWD Red Sports run the same 255/35 R20 tyre at each corner.
- One owner reported that 20x10 ET30 wheels on a 2017 AWD car at standard height cleared the rear calipers but poked roughly half an inch past the front arches.
- Many aftermarket wheels have a 73.1 mm bore. Use 73.1 to 66.1 mm hub-centric rings.
- M12x1.25 nuts are needed. Many other 5x114.3 cars use M12x1.5, which will not fit.
- Check full steering lock and suspension travel with the car loaded. Match wheel load rating, tyre load and speed ratings, fastener seats and brake clearance.
See it on your car.
Upload a photo and start with a look that suits the Q60. Try the wheels, colour and stance before you spend on parts.
An AI preview shows the look. It cannot verify physical fitment.
Run the numbers
These tools start with the 2.0t / 3.0t (Pure, Premium, Luxe, Sport), 19-inch front size. Choose your own trim or axle in the calculator if it differs.
Questions
What is the Infiniti Q60 bolt pattern?
The 2017–2022 Q60 uses 5x114.3, with a 66.1 mm centre bore and M12x1.25 wheel nuts.
Are Red Sport 400 wheels staggered?
On rear-wheel-drive cars, yes. From 2018 they are 20x9 ET40 at the front and 20x9.5 ET47 at the rear. The AWD Red Sport uses 20x9 ET40 at all four corners.
Will Q50 wheels fit a Q60?
The bolt pattern, bore and thread are the same, so they bolt on. Offsets and brake clearance still depend on the specific wheel, so check them against your car's brakes.
What is the Q60 wheel-nut torque?
108 Nm, about 80 lb-ft.
What size tyres does the Infiniti Q60 CV37 have?
Factory tyre (tire) sizes for the 2017–2022 Infiniti Q60 CV37 are 255/40 R19, 245/40 R19, 265/35 R19, 255/35 R20 and 275/30 R20, depending on trim, with wider rears on staggered setups. Your tyre placard shows the size for your car.
What wheel size does the Infiniti Q60 CV37 use?
Factory wheels are 19 × 9 inch, 19 × 9.5 inch, 20 × 9 inch and 20 × 9.5 inch, depending on trim. The stock table lists the offset for each.
What is the Infiniti Q60 CV37 centre bore?
66.1 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.
Specs checked against
- TireWheelGuide: 2017 Q60 factory sizes, bore and thread
- TireWheelGuide: 2020 Q60 factory sizes
- Wheel-Size: 2018 Q60 OE fitments
- Tiresize.com: 2017 Q60 tyre sizes by trim
- Tiresize.com: 2018 Q60 tyre sizes by trim
- Tiresize.com: 2021 Q60 tyre sizes by trim
- Hubcap Haven: OEM Q60 wheel sizes and offsets
- Wheel-Sizes.com: Q60 lug nut thread and torque
- InfinitiQ60.org: aftermarket wheel picture thread
- InfinitiQ60.org: 20x10 ET30 square setup at stock height
- InfinitiQ60.org: wheels for a stock-height Q60
This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.
Related cars
More guides from Infiniti or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.