2013–2020 · hatchback

Honda Fit / Jazz GK wheel fitment

The third-generation Fit and Jazz came on 15-inch steel or alloy wheels on lower grades and 16x6 alloys on EX, EX-L and Sport versions. Owners mostly want a wider wheel and a grippier 205-section tyre, either 15-inch for autocross or 16 and 17-inch for the street, without moving far from the factory offset.

4x100 bolt pattern · 56.1 mm centre bore · Stock wheels: 16 × 6, 15 × 6 inch · Stock tyres: 185/55 R16, 185/60 R15

Updated 2026-10-31 · High source confidence. Check your exact trim and market. How we check specs

Quick specs

Honda Fit / Jazz GK hub and fastener specifications
Specification	Value
Bolt pattern	4x100
Stock tyre sizes	185/55 R16 185/60 R15
Centre bore	56.1 mm
Fastener and thread	Wheel nut, M12x1.5
Tightening torque	108 Nm (confirm in your handbook)

Stock wheels and tyres

Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.

Factory wheels and tyres by trim and axle
Trim	Axle	Wheel	Tyre
Fit EX / EX-L / Jazz 16-inch alloy	Front and rear	16 × 6 inch, ET53	185/55 R16
Fit LX / Jazz, 15-inch	Front and rear	15 × 6 inch, ET50	185/60 R15

Explained in our guides

Read these before choosing wheels for the Fit / Jazz: they explain the offset, fitment and hub numbers in this guide.

Popular community setups

Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.

15x6.5 autocross size

Front and rear: 15 × 6.5 inch, ET45 · 205/50 R15

A FitFreak member runs Rota 15x6.5 ET45 wheels with 205/50 R15 Direzza Z1 tyres at standard ride height and reports no rubbing.

16x7 with 205/50 tyres

Front and rear: 16 × 7 inch, ET40 · 205/50 R16

Posted by GK owners on FitFreak alongside the factory specs. Lowered cars at ET40 to ET42 report front liner rub on dips unless they add around 1.3 to 1.5 degrees of negative camber.

17x7 at ET43

Front and rear: 17 × 7 inch, ET43 · 205/45 R17

Several FitFreak members run 17x7 at ET40 to ET43 with 205/45 R17, which is close to the factory tyre's diameter. One reported no rubbing at standard height on ET43.

Width and offset guidance

Offset range

ET40 to ET53

GK owners on 7-inch wheels mostly run ET40 to ET45. Below that, owners report front poke and rubbing unless they add negative camber.

Common width limit

Measure before ordering

A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.

These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.

Clearance notes

The factory 16-inch wheel is 16x6 ET53, confirmed by owners from the stamping on the back of the wheel. The US LX steel wheel is stamped 15x6 ET50.
Wheel nuts are M12x1.5, tightened to 108 Nm. Use nuts with the seat type the new wheel needs.
Lowered GKs on ET40 to ET42 wheels tend to rub the front liners on dips and at full lock. Owners fix it with camber bolts, tucking the liners and removing the top push pins.
Some lowered owners add a 10 mm rear spacer with longer studs so the rear sits as far out as the front. Use hub-centric spacers designed for 4x100 and a 56.1 mm hub.
Wheels with a larger bore than 56.1 mm need hub-centric rings.
Check full steering lock and suspension travel with the car loaded. Match wheel load rating, tyre load and speed ratings, fastener seats and brake clearance.

See it on your car.

Upload a photo and start with a look that suits the Fit / Jazz. Try the wheels, colour and stance before you spend on parts.

See it on your car

An AI preview shows the look. It cannot verify physical fitment.

Run the numbers

These tools start with the Fit EX / EX-L / Jazz 16-inch alloy front size. Choose your own trim or axle in the calculator if it differs.

Compare tyre sizes Compare wheel offsets Check tyre and rim width Find the same bolt pattern Convert offset to backspacing

Questions

What is the bolt pattern of the 2013–2020 Fit and Jazz?

4x100, with a 56.1 mm centre bore and M12x1.5 wheel nuts torqued to 108 Nm.

What are the factory wheel sizes on a GK Fit?

EX, EX-L and other 16-inch versions use 16x6 ET53 with 185/55 R16. The LX uses 15x6 ET50 with 185/60 R15.

What 17-inch size fits a GK Fit?

17x7 at ET40 to ET43 with 205/45 R17 is the setup owners report most. It is close to the factory tyre's diameter.

Will GD or GE Fit wheels fit a GK?

Yes. All three generations use 4x100 and a 56.1 mm hub bore, and the factory offsets are within a few millimetres of each other.

What size tyres does the Honda Fit / Jazz GK have?

Factory tyre (tire) sizes for the 2013–2020 Honda Fit / Jazz GK are 185/55 R16 and 185/60 R15, depending on trim. Your tyre placard shows the size for your car.

What is the Honda Fit / Jazz GK centre bore?

56.1 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.

What is the Honda Fit / Jazz GK wheel nut torque?

108 Nm (about 80 lb-ft) for the original nuts. Confirm in your handbook, especially with aftermarket wheels or nuts.

Specs checked against

This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.

Related cars

More guides from Honda or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.