2020–present · coupe / convertible
The C8 uses different wheel mounting dimensions from the front-engined C7. Stingray owners often keep the factory 19/20-inch diameters and reduce the offsets, while Z06 and E-Ray wheels are sized for wider bodywork.
5x120 bolt pattern · 66.9 mm centre bore · Stock wheels: 19 × 8.5, 20 × 11, 20 × 10, 21 × 13 inch · Stock tyres: 245/35 R19, 305/30 R20, 275/30 R20, 345/25 R21
Updated 2026-10-04 · High source confidence. Check your exact trim and market. How we check specs
| Specification | Value |
|---|---|
| Bolt pattern | |
| Stock tyre sizes | |
| Centre bore | 66.9 mm |
| Fastener and thread | Wheel nut, M14x1.5 |
| Tightening torque | 190 Nm (confirm in your handbook) |
Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.
| Trim | Axle | Wheel | Tyre |
|---|---|---|---|
| Stingray / Z51 | Front | 19 × 8.5 inch, ET52 | 245/35 R19 |
| Stingray / Z51 | Rear | 20 × 11 inch, ET64 | 305/30 R20 |
| Z06 / E-Ray | Front | 20 × 10 inch, ET35 | 275/30 R20 |
| Z06 / E-Ray | Rear | 21 × 13 inch, ET40 | 345/25 R21 |
Read these before choosing wheels for the Corvette: they explain the offset, fitment and hub numbers in this guide.
Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.
Threepiece documents MRR GF5 wheels with these sizes on a standard-height Z51 without reported rubbing. Approval is wheel-design specific.
A documented Weld Ventura setup on standard suspension uses the factory tyre sizes without reported rubbing. Check arch clearance again if the car is lowered.
Check the exact setup
There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.
Measure before ordering
A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.
These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.
Upload a photo and start with a look that suits the Corvette. Try the wheels, colour and stance before you spend on parts.
An AI preview shows the look. It cannot verify physical fitment.
These tools start with the Stingray / Z51 front size. Choose your own trim or axle in the calculator if it differs.
Stingray, Z51, Z06 and E-Ray use 5x120, a 66.9 mm centre bore and M14x1.5 wheel nuts. ZR1 is excluded from this specification because its rear mounting differs.
They are 245/35 R19 at the front and 305/30 R20 at the rear, on 19x8.5 ET52 and 20x11 ET64 wheels.
The Z06 wheels are intended for its wider bodywork. Their widths and offsets are not a direct Stingray fitment.
The Stingray owner's manual specifies 190 Nm for the factory wheel nuts.
Factory wheels are 19 × 8.5 inch, 20 × 11 inch, 20 × 10 inch and 21 × 13 inch, depending on trim. The stock table lists the offset for each.
66.9 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.
This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.
More guides from Chevrolet or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.