2019–present · SUV
The RS Q8 uses square 22 or 23-inch wheels around very large ten-piston front brakes, so smaller wheels are not an option. Most owners keep 23 inches and 295/35 R23 tyres, using spacers or lower-offset forged wheels to push the wheels out to the arches, often on lowering links.
5x112 bolt pattern · 66.5 mm centre bore · Stock wheels: 22 × 10, 23 × 10.5 inch · Stock tyres: 295/40 R22, 295/35 R23
Updated 2026-10-04 · High source confidence. Check your exact trim and market. How we check specs
| Specification | Value |
|---|---|
| Bolt pattern | |
| Stock tyre sizes | |
| Centre bore | 66.5 mm |
| Fastener and thread | Wheel bolt, M14x1.5 |
| Tightening torque | 160 Nm (confirm in your handbook) |
Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.
| Trim | Axle | Wheel | Tyre |
|---|---|---|---|
| RS Q8, 22-inch standard wheels | Front and rear | 22 × 10 inch, ET18 | 295/40 R22 |
| RS Q8 / RS Q8 performance, 23-inch wheels | Front and rear | 23 × 10.5 inch, ET18 | 295/35 R23 |
Read these before choosing wheels for the RS Q8: they explain the offset, fitment and hub numbers in this guide.
Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.
An RS Q8 owner on AudiWorld runs 12 mm front and 15 mm rear spacers on the factory wheels with no problems, giving about ET6 front and ET3 rear. Use longer ball-seat bolts to suit the spacers.
Element Wheels shows this RS Q8 fitment with the factory tyre size. Builds like this are often paired with lowering links to close the arch gap.
Owners use the factory 22-inch wheels with 275/40 R22 winter tyres. Some have raised concerns about rubbing with certain winter tyre models, so check clearance on full lock.
Check the exact setup
There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.
Measure before ordering
A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.
These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.
Upload a photo and start with a look that suits the RS Q8. Try the wheels, colour and stance before you spend on parts.
An AI preview shows the look. It cannot verify physical fitment.
These tools start with the RS Q8, 22-inch standard wheels front size. Choose your own trim or axle in the calculator if it differs.
5x112 with a 66.5 mm centre bore. It uses M14x1.5 ball-seat bolts tightened to 160 Nm.
22x10 ET18 with 295/40 R22 tyres as standard, or 23x10.5 ET18 with 295/35 R23 tyres. Both setups are square.
Plan on 22 inches. That is the smallest wheel Audi fits over the 420 mm or 440 mm front discs, owners report 20-inch wheels will not clear, and no 21-inch fitment is confirmed.
On the factory 10.5-inch rim, about 305 wide. Builds with 325/30 R23 tyres use 12-inch wide wheels.
Yes. They share the 5x112 hub and 66.5 mm bore, and SQ8 owners run RS Q8 23s with 295/35 R23 tyres without modification.
Factory tyre (tire) sizes for the 2019–present Audi RS Q8 4M are 295/40 R22 and 295/35 R23, depending on trim. Your tyre placard shows the size for your car.
66.5 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.
160 Nm (about 118 lb-ft) for the original bolts. Confirm in your handbook, especially with aftermarket wheels or bolts.
This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.
More guides from Audi or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.