2013–2018 · estate
The C7 RS6 Avant came on 9.5-inch wheels in 20 or 21 inches, which leaves room under the arches. Owners usually fit 10.5-inch wheels in 21 or 22 inches, often with a modest drop, and pick a spoke design that clears the large front brakes.
5x112 bolt pattern · 66.5 mm centre bore · Stock wheels: 20 × 9.5, 21 × 9.5 inch · Stock tyres: 275/35 R20, 285/30 R21
Updated 2026-10-04 · High source confidence. Check your exact trim and market. How we check specs
| Specification | Value |
|---|---|
| Bolt pattern | |
| Stock tyre sizes | |
| Centre bore | 66.5 mm |
| Fastener and thread | Wheel bolt, M14x1.5 |
| Tightening torque | 120 Nm (confirm in your handbook) |
Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.
| Trim | Axle | Wheel | Tyre |
|---|---|---|---|
| RS6 Avant, 20-inch standard wheels | Front and rear | 20 × 9.5 inch, ET21 | 275/35 R20 |
| RS6 Avant / RS6 Performance, 21-inch wheels | Front and rear | 21 × 9.5 inch, ET25 | 285/30 R21 |
Read these before choosing wheels for the RS6 Avant: they explain the offset, fitment and hub numbers in this guide.
Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.
An RS246 owner runs this on H&R 20 mm lowering with no spacers and reports no rubbing, although the wheel sits closer to the suspension than stock. LFI's suggested 21-inch C7 spec is a similar 21x10.5 ET20 with 285/30 R21.
Shown in the Wheel Front gallery on Vossen HF-4T wheels. The 295 tyre is tight, so get a proper alignment and keep an eye on the arch liners. Another gallery car runs 22x10.5 ET35 with 15 mm front and 20 mm rear spacers.
One RS246 owner runs 15 mm spacers on top of ET20 (about ET5 effective), lowered on adjustable air-suspension links with steel brakes, and reports no rubbing. Another owner trying something similar had serious front rubbing, so treat this as the limit, not a safe default.
Check the exact setup
There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.
Measure before ordering
A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.
These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.
Upload a photo and start with a look that suits the RS6 Avant. Try the wheels, colour and stance before you spend on parts.
An AI preview shows the look. It cannot verify physical fitment.
These tools start with the RS6 Avant, 20-inch standard wheels front size. Choose your own trim or axle in the calculator if it differs.
5x112 with a 66.5 mm centre bore. It uses M14x1.5 ball-seat bolts torqued to 120 Nm.
20x9.5 ET21 with 275/35 R20 tyres, or 21x9.5 ET25 with 285/30 R21 tyres. Both are square.
Some do. Owners have fitted 20-inch BBS designs over ceramics, but the spokes must angle sharply away from the centre to clear the calipers. Check the exact wheel.
285/30 R21 is the usual choice. It matches the factory 21-inch tyre size and owners run it without rubbing when slightly lowered.
Factory tyre (tire) sizes for the 2013–2018 Audi RS6 Avant C7 are 275/35 R20 and 285/30 R21, depending on trim. Your tyre placard shows the size for your car.
66.5 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.
120 Nm (about 89 lb-ft) for the original bolts. Confirm in your handbook, especially with aftermarket wheels or bolts.
This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.
More guides from Audi or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.