2017–2024 · coupe / sportback
The B9 RS5 coupe and Sportback leave the factory on 9-inch wheels, which look narrow under the wide RS arches. Owners usually go square at 10 to 10.5 inches wide, either a light 19-inch set for driving or a 20-inch set at around ET20 to ET25 for a flush look.
5x112 bolt pattern · 66.5 mm centre bore · Stock wheels: 19 × 9, 20 × 9 inch · Stock tyres: 265/35 R19, 275/30 R20
Updated 2026-10-04 · High source confidence. Check your exact trim and market. How we check specs
| Specification | Value |
|---|---|
| Bolt pattern | |
| Stock tyre sizes | |
| Centre bore | 66.5 mm |
| Fastener and thread | Wheel bolt, M14x1.5 |
| Tightening torque | 120 Nm (confirm in your handbook) |
Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.
| Trim | Axle | Wheel | Tyre |
|---|---|---|---|
| RS5 coupe / Sportback, 19-inch standard wheels | Front and rear | 19 × 9 inch, ET24 | 265/35 R19 |
| RS5 coupe / Sportback, 20-inch optional wheels | Front and rear | 20 × 9 inch, ET26 | 275/30 R20 |
Read these before choosing wheels for the RS5: they explain the offset, fitment and hub numbers in this guide.
Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.
Apex's main B9 RS5 fitment, sitting flush at both ends without rubbing on compression. A good choice for track days or a lighter road set. The wheel design must clear the RS front calipers.
Widely run on RS5s at standard height. 285/30 R20 fills a 10-inch rim with no stretch. For a 10.5-inch rim, ET25 suits standard height and ET22 to ET23 suits a lowered car.
A documented RS5 Sportback build on HRE FF01 wheels, lowered about 1 inch on ABT height-adjustable springs. This tucks the wheel face neatly inside the arch while keeping the factory tyre size.
ET20 to ET26
Square 9 to 10.5-inch setups between ET20 and ET25 are well documented. A 10.5-inch wheel at ET35 is reported to touch suspension parts, so it needs spacers.
10.5 inch
10.5-inch wheels at about ET25 with 285 or 295 tyres are run on unmodified RS5 arches. 295s may need small spacers or a flat-head arch screw.
These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.
Upload a photo and start with a look that suits the RS5. Try the wheels, colour and stance before you spend on parts.
An AI preview shows the look. It cannot verify physical fitment.
These tools start with the RS5 coupe / Sportback, 19-inch standard wheels front size. Choose your own trim or axle in the calculator if it differs.
5x112 with a 66.5 mm centre bore and M14x1.5 ball-seat bolts, torqued to 120 Nm.
19x9 ET24 with 265/35 R19 tyres as standard, and 20x9 ET26 with 275/30 R20 tyres as an option. Both are square.
Audi does not offer one. Some owners say particular 18-inch designs clear the steel brakes, but it is not confirmed. With ceramic brakes, stay at 19 inches or above.
285/30 R20. It sits without stretch on a 10-inch rim and stays close to the factory rolling diameter.
About ET25 at standard height or ET22 to ET23 when lowered. ET35 at that width is reported to hit suspension parts.
66.5 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.
120 Nm (about 89 lb-ft) for the original bolts. Confirm in your handbook, especially with aftermarket wheels or bolts.
This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.
More guides from Audi or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.