22-inch rim · tyre size comparison
265/35 R22 vs 295/30 R22
295/30 R22 is 8.5 mm (0.33 in) shorter than 265/35 R22, a -1.14% difference in overall diameter. That is inside the ±3% limit commonly used to screen a tire size change; it is a nominal calculation, not a fitment approval.
- Diameter difference
- -8.5 mm
- -0.33 in · -1.14%
- Indicated 70 mph
- 69.2 mph
- Actual speed on 295/30 R22, if the speedometer was accurate on 265/35 R22.
- Sidewall height
- -4.25 mm
- 92.75 mm to 88.5 mm.
Dimensions side by side
| Measurement | 265/35 R22 | 295/30 R22 | Difference |
|---|---|---|---|
| Overall diameter | 744.3 mm29.3 in | 735.8 mm28.97 in | -8.5 mm (-1.14%)-0.33 in |
| Section width | 265 mm10.43 in | 295 mm11.61 in | +30 mm+1.18 in |
| Sidewall height | 92.75 mm3.65 in | 88.5 mm3.48 in | -4.25 mm-0.17 in |
| Circumference | 2,338.29 mm92.06 in | 2,311.58 mm91.01 in | -26.7 mm-1.05 in |
| Rim diameter | 558.8 mm22 in | 558.8 mm22 in | 0 mm0 in |
| Revolutions per mile | 688.26 | 696.21 | +7.95 |
| Revolutions per km | 427.66 | 432.6 | +4.94 |
Calculated from the nominal size codes, without load or tread wear. Real tyres vary by model, rim width and pressure, so the exact tyre's published dimensions take priority.
Speedometer with 295/30 R22
If the speedometer was accurate on 265/35 R22, fitting 295/30 R22 means the car is travelling 1.14% slower than it shows, and the odometer over-records distance by about the same amount.
| Speedometer shows | Actual on 295/30 R22 | Difference |
|---|---|---|
| 30 mph | 29.66 mph | -0.34 mph |
| 50 mph | 49.43 mph | -0.57 mph |
| 60 mph | 59.31 mph | -0.69 mph |
| 70 mph | 69.2 mph | -0.8 mph |
| 50 km/h | 49.43 km/h | -0.57 km/h |
| 100 km/h | 98.86 km/h | -1.14 km/h |
UN ECE Regulation 39, used in the UK and EU, does not allow a speedometer to show less than the true speed, so many read slightly high from the factory. A shorter tyre adds to it. Calibration varies by car; these figures are the tyre-size effect only.
What changes from 265/35 R22 to 295/30 R22
Wheels
Both fit 22-inch wheels. Our rim-width starting estimate is 8.5 to 9.5 inches for 265/35 R22 and 9.5 to 10.5 inches for 295/30 R22, so a 9.5-inch wheel sits in both ranges. The exact tyre's approved rim range takes priority.
Sidewall and ride comfort
295/30 R22 has 4.25 mm less sidewall (88.5 vs 92.75 mm). A shorter sidewall usually sharpens steering response, but rides a little firmer and leaves the rim more exposed to potholes and kerbs.
Contact width
295/30 R22 is 30 mm wider in nominal section width (11.3%). A wider tyre usually puts a wider, shorter contact patch on the road, which can help dry grip, but it may follow ruts more, clear standing water less readily and add some rolling resistance.
Wheel well clearance
Ride height changes by about -4.3 mm, and the top of the tyre moves the same distance away from the arch. On the same wheel width and offset, each sidewall moves about 15 mm further out towards the arch lip and further in towards the suspension. Check clearance at full steering lock and full suspension compression, especially on a lowered car.
Gearing
The effective final drive changes by +1.16%: 3,000 rpm at a given road speed becomes about 3,030 rpm. Gearing gets slightly shorter, so acceleration in each gear sharpens and cruising revs rise.
ABS, stability control and AWD
These systems compare wheel speeds. Fit the same size on both ends of an axle; with a 1.1% diameter gap, never mix 265/35 R22 and 295/30 R22 on an AWD car, and follow the car maker's rolling-circumference limits, which can be much tighter than 3%.
General tendencies from the nominal numbers, not a test of any tyre. Load index, speed rating, tyre construction and the car's approved sizes matter more than these rules of thumb.
Explained in our guides
- Plus-sizing wheels: tyre diameter and speedometer changesWork through a 17 to 18 inch wheel change, compare tyre diameters and speedometer effects, and understand why a 3% rule cannot approve fitment.
- Staggered vs square wheels: tyres, rotation and AWDCompare square and staggered wheel setups, calculate front-to-rear tyre diameter, and understand rotation limits and all-wheel-drive requirements.
- How to read a tyre size, load index and sidewall markingsDecode tyre width, aspect ratio, rim diameter, load and speed markings, then calculate sidewall height and diameter using a 225/45 R17 example.
Cars in our guides using these sizes
Factory trims and popular community setups from our fitment guides. A popular setup is not a factory approval; each guide explains its trims, axles and clearance limits.
265/35 R22
None of our car guides list 265/35 R22 yet. That says nothing about whether it is made or approved for a car; it just isn't in our fitment data.
295/30 R22
- Audi RS7 Sportback C8 (2019–present)Popular setup
Questions
Can I use 295/30 R22 instead of 265/35 R22?
Both fit 22-inch wheels. The diameter difference is -1.14%, inside the ±3% screening limit. That does not approve fitment: check the car maker's approved sizes, load index, speed rating, rim width and clearance first.
How much bigger is 295/30 R22 than 265/35 R22?
Overall diameter is 8.5 mm (0.33 in) smaller: 735.8 vs 744.3 mm. Section width is 30 mm wider, and the sidewall is 4.25 mm shorter. These are nominal figures; real tyres vary by model and rim width.
Will 295/30 R22 change my speedometer reading?
Yes, by 1.14%. If the speedometer was accurate on 265/35 R22, an indicated 60 mph would be about 59.3 mph on 295/30 R22, and an indicated 100 km/h about 98.9 km/h. You would be going slower than the speedometer shows.
Which is better, 265/35 R22 or 295/30 R22?
Neither in general. 265/35 R22 has the taller sidewall, which usually rides more comfortably; 295/30 R22 usually steers more sharply. 295/30 R22 is wider, which can help dry grip; the narrower size is usually better in standing water and snow. The size listed for your car's trim, on its placard or in the handbook, is the safe default.
Check the exact tyre
Size codes give nominal dimensions. Before buying, confirm the size is approved for your car and check the exact tyre's load and speed ratings and published dimensions.