Narrowbody RWD square daily
- Front and rear
- 20 × 10 inch, ET19 · 275/40 R20
Apex lists this as a direct fit for the narrowbody rear-wheel-drive Charger. Its wheel design clears the relevant factory brakes; do not transfer this offset to AWD.
2011–2023 · saloon
Dodge Charger LD wheel fitment
The Charger has very different wheel requirements across rear-wheel drive, all-wheel drive and widebody versions. Wider 20-inch wheels are common on rear-wheel-drive cars, but AWD models need much higher offsets.
5x115 bolt pattern · 71.6 mm centre bore · Stock wheels: 17 × 7, 18 × 7.5, 20 × 8, 20 × 9, 20 × 9.5, 20 × 11, 19 × 7.5 inch · Stock tyres: 215/65 R17, 235/55 R18, 245/45 R20, 275/40 R20, 305/35 R20, 235/55 R19
Updated 2026-10-04 · Medium source confidence. Check your exact trim and market. How we check specs
Quick specs
| Specification | Value |
|---|---|
| Bolt pattern | |
| Stock tyre sizes | |
| Centre bore | 71.6 mm |
| Fastener and thread | Wheel nut, M14x1.5 |
| Tightening torque | Confirm in your handbook |
Stock wheels and tyres
Factory options vary by trim and market. Match your car to the row below and check its tyre placard before using it as a baseline.
| Trim | Axle | Wheel | Tyre |
|---|---|---|---|
| SXT RWD, standard 17-inch | Front and rear | 17 × 7 inch, ET24 | 215/65 R17 |
| SXT RWD, 18-inch | Front and rear | 18 × 7.5 inch, ET24 | 235/55 R18 |
| R/T / GT RWD, 20-inch | Front and rear | 20 × 8 inch, ET24 | 245/45 R20 |
| R/T Scat Pack, narrowbody standard wheels | Front and rear | 20 × 9 inch, ET22.5 | 245/45 R20 |
| SRT 392 / Hellcat, narrowbody 9.5-inch wheels | Front and rear | 20 × 9.5 inch, ET18.5 | 275/40 R20 |
| Scat Pack / Hellcat Widebody | Front and rear | 20 × 11 inch, ET-2.5 | 305/35 R20 |
| SXT / GT AWD, 19-inch | Front and rear | 19 × 7.5 inch, ET55 | 235/55 R19 |
Explained in our guides
Read these before choosing wheels for the Charger: they explain the offset, fitment and hub numbers in this guide.
- Wheel offset explained: choosing ET without guessingUnderstand positive and negative wheel offset, calculate inner clearance and outer position, and choose an ET using measurements from your own car.
- Flush, poke and tucked fitment: measure the whole tyreUnderstand flush, poked and tucked wheels, calculate how width and offset change the look, and check clearance beyond a parked side-on photograph.
- Hub-centric vs lug-centric wheels: choosing hub ringsLearn what hub rings do, how to specify their inner and outer diameters, and why centring, wheel seats and vibration need separate checks.
Popular community setups
Starting points for a build. Read the notes with each setup, especially if your car is lowered or has different brakes.
Narrowbody RWD staggered grip
- Front
- 20 × 10 inch, ET19 · 275/40 R20
- Rear
- 20 × 10.5 inch, ET22 · 305/35 R20
Apex's direct-fit staggered combination gives the rear a 305-section tyre. This is for standard narrowbody RWD geometry; recheck clearance on lowered cars.
Width and offset guidance
Offset range
Check the exact setup
There is no confirmed range for this car yet. Compare a known wheel with your proposed size and measure both sides.
Common width limit
Measure before ordering
A maximum width has not been confirmed. Tyre shape, ride height and alignment all change the available space.
These figures belong to the setups described here. Combining the widest wheel with either end of the offset range does not guarantee a safe fit. For how ET moves the wheel in and out, read wheel offset explained; for how far the tyre can sit out, see flush, poke and tucked fitment.
Clearance notes
- There is no single torque figure for every Charger in this entry. Later Dodge manuals specify 176 Nm for base models and 150 Nm for SRT models; use the handbook and any performance supplement for the exact model year and trim. The scalar torqueNm field is therefore omitted.
- Retailer torque charts disagree with some Dodge manuals, including earlier model years. The vehicle-specific manufacturer manual takes precedence over a generation-wide chart.
- AWD factory offsets are much higher than RWD offsets. The listed popular RWD combinations are not AWD recommendations.
- Widebody wheels have substantially lower offsets and require the matching bodywork. Narrowbody and widebody wheels are not interchangeable just because both use 5x115.
- Some retailers describe the hub as 71.5 mm; the fitment database specifies 71.6 mm. Order wheels and hub rings explicitly approved for this application. Do not force an undersized bore onto the hub.
- Confirm spoke clearance against the fitted Brembo package. A 5x114.3 wheel is not the correct 5x115 mounting pattern.
- Earlier SRT8, police Pursuit and individual appearance-package wheel options are omitted; the rows cover the main later civilian combinations.
- Check full steering lock and suspension travel with the car loaded. Match wheel load rating, tyre load and speed ratings, fastener seats and brake clearance.
See it on your car.
Upload a photo and start with a look that suits the Charger. Try the wheels, colour and stance before you spend on parts.
An AI preview shows the look. It cannot verify physical fitment.
Run the numbers
These tools start with the SXT RWD, standard 17-inch front size. Choose your own trim or axle in the calculator if it differs.
Questions
What is the Charger bolt pattern?
It is 5x115, with a nominal 71.6 mm centre bore and M14x1.5 wheel nuts.
Will rear-wheel-drive Charger wheels fit an AWD model?
Do not assume so. The factory 19-inch AWD package uses ET55, while common RWD wheels have much lower offsets. AWD requires a separately checked fitment.
Can a narrowbody Charger run 305 rear tyres?
Apex lists 305/35 R20 tyres on 20x10.5 ET22 rear wheels, paired with 20x10 ET19 fronts and 275/40 R20 tyres, for narrowbody RWD cars.
What torque do Charger wheel nuts need?
Check the exact model's manual. Later base-model specifications are 176 Nm and SRT specifications are 150 Nm, but those figures must not be applied indiscriminately across all years and special editions.
What size tyres does the Dodge Charger LD have?
Factory tyre (tire) sizes for the 2011–2023 Dodge Charger LD are 215/65 R17, 235/55 R18, 245/45 R20, 275/40 R20, 305/35 R20 and 235/55 R19, depending on trim. Your tyre placard shows the size for your car.
What wheel size does the Dodge Charger LD use?
Factory wheels are 17 × 7 inch, 18 × 7.5 inch, 20 × 8 inch, 20 × 9 inch, 20 × 9.5 inch, 20 × 11 inch and 19 × 7.5 inch, depending on trim. The stock table lists the offset for each.
What is the Dodge Charger LD centre bore?
71.6 mm. Aftermarket wheels with a larger bore need hub-centric rings sized to it.
Specs checked against
- Project 6GR Dodge mounting and factory wheel specifications
- 2020 Charger wheel specification database
- Apex Charger narrowbody RWD fitment guide
- 2023 Charger / Challenger performance features guide
This guide is a starting point, not a fitment guarantee. Specs can differ by market, trim and previous modifications. Confirm all sizes, clearances and fastener requirements with a qualified wheel and tyre professional before buying or fitting parts.
Related cars
More guides from Dodge or cars with the same bolt pattern. A matching pattern alone does not make a wheel interchangeable.